github rinkhals-community/Rinkhals 20261118_03_test
Rinkhals 20261118_03_test

pre-releaseone hour ago

Greetings Citizens of Rinkhalsvania!

This is a sixth test build on the way to the next release. It has everything from 20261118_02_test, plus one change that takes a lot of pointless work off the printer's processor.

What's new since 20261118_02_test

  • The web portal no longer spikes the CPU while it's open (#250). With the portal's dashboard or Apps page open in a browser, the printer ran every app's status script every few seconds. On our Kobra S1 that was about 40 small programs started per second, and the CPU hit 90-100% every few seconds for as long as the tab stayed open. The portal now asks each app once and then just watches whether the app's processes are still there, which costs nothing. An app is only asked again when something changed.

  • The printer does less while sitting idle (#250). Anycubic's firmware restarts a command shell on a console that doesn't exist, about once a second, forever. Each of those loaded the Rinkhals tools, which started about ten small programs every time... for nothing. Loading the tools now starts one. Logging in over SSH and every app start and stop get a little quicker too.

  • The portal's service buttons check what they're asked to do (#250). The dashboard's start, stop and restart buttons passed the app name to the printer's shell as received. It sat behind the portal's login, so it wasn't a way in, but it's now checked and quoted properly.

What we measured on our Kobra S1, not printing, with Klipper (vanilla) and HelixScreen running:

Programs started per second Highest CPU in one second
Before, dashboard open about 41 96%
Before, portal closed 13.5 56%
Now, dashboard open 5.8 48%

One thing to know: an app that you start or stop outside the portal, from an SSH terminal for example, can take a couple of minutes to show its new state in the portal. Anything you do in the portal or on the touch screen shows right away.

Please help us test

  • Does Rinkhals start normally after the update, and does the Rinkhals entry in Settings open the Rinkhals menu?
  • Open the web portal (http://<printer-ip>:8090) and leave the dashboard open for a few minutes. Does the CPU figure stay calm, and do the service cards show the right state?
  • On the portal's Apps page, start, stop, enable and disable an app. Does the page show the new state right away?
  • Enable or disable an app from the touch screen with the portal's Apps page open. Does the page follow within a few seconds?
  • Do your apps still start at boot like before?
  • Do Mainsail or Fluidd connect, and does a print from your slicer start and finish normally?

We measured this on our Kobra S1. We have not rebooted a printer with this build yet, and we haven't tried it on any other model. The tools file gives the same values as the old one on our printer, so we don't expect trouble... but please tell us if something doesn't start.

If something doesn't work, a debug bundle from the Management page of the Rinkhals web portal would help a lot.

Known issues

These are open and not fixed in this release.

  • A reboot with Klipper (vanilla) or a tunneled Klipper running still hangs on the Kobra 3 family and the Kobra S1 Max. Switch the printer off and on instead of rebooting. On the Kobra S1 this was fixed in 20261118_02_test.
  • The new app dependency messages on the touch screen and in the web portal's Apps page haven't been tried on a printer yet.
  • On the Kobra S1 with 2.7.3.7, the Mainsail and Fluidd Heightmap shows the saved mesh instead of the live one during a print. The live view stays limited to 2.7.2.7 until we've checked it on the new firmware.
  • #205 - on the Kobra S1 Max, the head still stays over the last probe point after a calibration started from Mainsail. It doesn't affect the mesh.

Report findings to https://github.com/rinkhals-community/Rinkhals/issues with a debug bundle.

Full Changelog: 20261118_02_test...20261118_03_test

Don't miss a new Rinkhals release

NewReleases is sending notifications on new releases.