v1.1.0-rc.3
Added
- Material presets heat the bed and chamber - a material preset now sets the bed along with the nozzle on every screen: the Filament panel, the Home screen's Preheat widget and the nozzle presets on the temperature graph. On a printer with a chamber heater, a preset also sets the chamber when the material has a chamber temperature. With Settings > Printing > Material presets heat the bed and chamber turned off, a preset heats only the nozzle, and the bed and the chamber keep the targets they had. Each printer keeps its own setting.
- Readable panels on ultrawide screens - on a screen much wider than it is tall, such as 1480x320 or 1920x440, panels and overlays stop at 2.4 times the screen height and stay next to the navigation bar, so a settings list or the jog pad is no longer stretched across the whole display. The home screen, print file list, Print Status, bed mesh and the AMS screens still use the full width. Screens such as 800x480, 1024x600 and portrait panels look the same as before.
Changed
- Temperature rows read the target after the reading - on the Controls temperature card and the Filament panel, each heater row reads like "Nozzle 205°C / 210°", with the reading colored by its heating state and the target in smaller text, or "/ Off" when no target is set. The separate target buttons are gone: tap a row to open the temperature graph on that heater and set its target there. Where the card has room, the line under each row now says Heating, At target or Cooling.
- Temperature graph chart keeps its height in portrait - on portrait screens such as 320x480, the temperature graph's sensor chips stay on one line that scrolls sideways, and the nozzle buttons are a little shorter, so the chart keeps a readable height with six tools.
- One tool choice for Controls, Filament and the temperature graph - on multi-head printers the Controls temperature card, the Filament panel and the temperature graph aim at the same tool, so picking a tool on any of them shows it on all three. A tool change still moves them to the mounted tool, and picking a tool never changes tools.
- Tool choosers use the tool switcher's cells - the Controls temperature card has a small tool button in its header that opens the Home tool switcher's picker, highlighting the tool the card shows and leaving out Park and Open feeder. The Filament panel and the temperature graph choose a tool from a row of the same cells, each with its filament color, in place of the tool dropdown and the numbered buttons. Every chooser numbers tools the way the nozzle row does, so a cell and "Nozzle 2" always agree.
- Pick up and Park everywhere - putting a tool on the carriage is called Pick up on every screen, matching the Filament panel: the filament system's slot menu, its sidebar (Pick up...), the tool picker for loading and its step list. Park stays Park, and the confirmation still asks "Switch to Tool 2?".
- Filament panel in cards - the Filament panel is laid out in cards like the Controls panel. The Temperature card at the top left shows the same rows as Controls, with the nozzle row for the tool the panel acts on, above the graph and the lane bars. On the right, the Material card holds the presets, and the Operations card holds compact Load, Unload, Purge, Extrude and Retract buttons. On a multi-head printer the Operations card also holds the row of heads and a Pick up or Park button with its own icon, and the Multi-Filament card keeps a smaller Manage button. The whole row of lane bars opens the filament system panel. On portrait screens the material presets share one row with Cool Down in the Material card's header, and on a multi-head printer the lane bars move into the Operations header, ending in a chevron.
- Print Status fits ultrawide screens - on very wide screens such as 1480x320 and 1920x440, Print Status now lays its content out in columns instead of stretching the normal layout. The model preview is a square at the full height, the progress, times, layer, filament and next job sit in a column with larger type, the printer picture keeps its natural shape with its callouts, a new card lists the nozzle, bed and chamber temperatures with their targets alongside speed, flow and the fans, and Pause, Tune, More and Cancel stack on the right. Tapping a temperature opens the temperature graph, and tapping speed opens Print Tune.
Fixed
- Snapmaker U1 on stock firmware updates from the screen - stock-firmware Snapmaker U1 installs can now update HelixScreen from the screen with Settings > Updates, like other printers. They read "Managed by your firmware" and offered no updates before. A U1 running the HelixScreen that PAXX Extended Firmware installs as a firmware component still leaves updates to the firmware (#2131).
- Reprint on Print Status runs the pre-print checks - the Reprint button on the Print Status screen now checks for enough filament, an empty lane, a material mismatch, an unassigned tool and the other pre-print checks before it starts, just like starting the file from the file list. A check that warns asks first, and Cancel starts nothing.
- No tool chooser for lanes into one hotend - a printer with one hotend and a multi-material system, such as AFC, Happy Hare or a CFS, no longer shows a T0 to T3 tool dropdown on the Filament panel. Those lanes feed one nozzle, so the panel keeps Manage and the lane bars, and Load and Unload act on the lane in the toolhead.
- XY on the Motion home bar - the Motion panel's home bar now shows an XY button, like the one on the Controls panel, on printers that home their axes separately. Where the bar has room for five buttons at a comfortable touch size, such as on 1024x600, wide strip and portrait screens, it shows All, X, Y, XY and Z. On narrower bars, such as on an 800x480 screen, it shows XY, X, Y and Z, because the home button in the middle of the jog pad already homes all axes.
- Tool lists no longer repeat the tool number - when positions are numbered from zero, the tool choosers on the Controls and Filament panels and the other tool lists showed "Tool 0 (T0)", saying the same number twice. They now show "Tool 0". Numbered from one, they still show "Tool 1 (T0)", so the screen's number and the G-code name both stay visible, and a tool with its own name still shows that name.
- Picking up a tool onto an empty carriage shows the pickup steps - on a Medusa HC, picking up a tool with no tool mounted showed the steps of a filament load, including Heat nozzle and Purge, in the progress list. It now shows the steps of the tool change itself. Only the list was wrong: the pickup never heated or purged.
- AFC lanes keep their temperatures when you unlink a spool - unlinking a Spoolman spool from an AFC lane made AFC forget the lane's nozzle and bed temperatures, so the next load heated to AFC's default for the material. HelixScreen now sends the temperatures from the spool editor back to AFC after the unlink, on AFC v1.2.0 and newer.
- A finished print wakes the display on Print Status - when a print ended while the Print Status screen was open, the display stayed asleep. On panels that keep showing their last picture while asleep, the screen kept showing the print as running, with its progress and Pause and Cancel buttons, until someone touched it. The end of a print now wakes the display on Print Status just as it does on every other screen, unless print completion alerts are turned off.
- Tool changes from the Filament panel on Reforge - on a Creator 5 Pro running Reforge without AFC, picking up a tool from the Filament panel was rejected with "TOOL must be T0..T3", so Load and Unload could not be used either. HelixScreen now sends the tool number in the form Reforge accepts.
- Fan readouts follow the active tool on tool changers - on a tool changer where every tool has its own part cooling fan and hotend fan, the Part and HE readouts beside the printer picture on Print Status and the Fan readout on the Home printer picture now show the fans of the tool that is printing. Before, they could stay on the first tool's fans while another tool printed, even though the nozzle temperature beside them followed the active tool.
- Aux fan readout leaves out tool fans on tool changers - the Aux readout beside the printer picture on Print Status no longer shows a parked tool's part cooling fan or hotend fan. When the printer has no other fan to show there, the readout is hidden.
- MPC calibration names a tool's part fan correctly - on a tool changer whose tools name their part fan without the
fan_genericprefix, switching the heater calibration to MPC now writes the tool's part fan as itscooling_fan. Before, it left the cooling fan out. - The installer no longer edits Z-Mod's own moonraker.conf on the AD5X - on a FlashForge AD5X running Z-Mod, the installer added HelixScreen's update stanza to the moonraker.conf that Z-Mod keeps in its own git tree. Moonraker then reported Z-Mod as modified and refused to update it, and recovering needed a shell. The installer now finds Z-Mod's tree, writes the stanza to the user moonraker.conf that Z-Mod's file includes, and leaves Z-Mod's file alone. When an earlier install already edited it, the installer says which updates are blocked and prints the command that restores the file. (thanks @catduckgnaf)
- No second heater shutdown after a print error on Jacobean's K2 Plus firmware - HelixScreen sends TURN_OFF_HEATERS when a print fails, because Klipper leaves the heaters on after an error. Jacobean's firmware for the Creality K2 Plus already turns the heaters off itself on an error, so HelixScreen now leaves it to the firmware on that printer. (thanks @Jacob10383)