github prestonbrown/helixscreen v1.1.0-beta.4

latest releases: v1.1.0-rc.5, v1.0.11, v1.1.0-rc.4...
pre-releaseone month ago

v1.1.0-beta.4

The fourth beta of 1.1. It adds Lua plugins, which put their own tiles, screens and
settings on the printer's screen, a Bed tab on the Motion screen, and a 32-bit Android
build. Belt Tension is rebuilt to compare both belts the way Shake&Tune
does. Most of the rest is fixes: CFS chains with a box switched off, ACE toolchanges,
printing from a USB stick, touch on rotated screens, and a long list of rare crashes. Many
screens now give their memory back when you close them.

Known issues (K-Touch alpha)

  • Print Files thumbnails mostly fail to load and can stall the screen for a few seconds
    at a time on folders with many files.
  • Opening a file's details can occasionally reboot the panel.

Both are fixed for the next beta. Other platforms are not affected.

Upgrading from beta.3?

  • Configure PRINT_START is gone from Advanced. The beta macro rewrite is removed. The
    pre-print skip options on the print file screen work as before.
  • Printing from a USB stick copies the file first. Print and Add to Queue upload the file
    to usb_prints/ in your G-code folder, with progress, then print that copy. Files on the
    stick can no longer be deleted from the screen.
  • Screens slide in from the right in portrait too, with a left back arrow, the same as
    landscape.

Added

Plugins

  • Lua plugins - drop a plugin into helixscreen/plugins in your printer's config folder
    and HelixScreen picks it up, on every printer you connect to. A plugin can add home screen
    tiles, its own screens and a settings page, and draw charts. Each one runs in a sandbox with
    its own memory and time limits, and asks before it gets access to G-code, Moonraker or the
    network. Settings > Plugins lists them, and nothing runs until you enable it there. A
    plugin that changes on the printer reloads in place. Two example plugins (a temperature
    sparkline and an LED effects tile) and an author guide are in the HelixScreen repository.
    Not available on Android yet.

Motion

  • Bed tab - tap the plate to send the toolhead there, or drag and it follows your finger.
    Below the new Bed Map Clearance setting (5mm by default) the first move lifts Z first, and
    the readout says so before you tap. The tab is disabled during a print and offers Home when
    the printer is not homed.

Calibration

  • Belt Tension is rebuilt around resonance sweeps (#1721) - still a beta, under Advanced >
    Calibration on CoreXY printers with an accelerometer. Instead of listening to a plucked belt,
    it runs a resonance sweep on each belt path and compares the two curves, leading with how
    similar they are and pairing up the peaks, the way Shake&Tune compares belts.

Android

  • A 32-bit Android APK - devices that refused the app with "no matching ABIs" can install
    helixscreen-android-armv7: the Echo Show 5 (2nd gen) on LineageOS, Fire tablets and older
    phones. Low-density screens like the Echo Show's are drawn at full size instead of at half.

BTT K-Touch (alpha)

  • HelixScreen firmware for the BigTreeTech K-Touch - the release now carries
    helixscreen-esp32-ktouch firmware for the standalone ESP32 touchscreen. It joins your
    Wi-Fi and talks to your printer's Moonraker like a remote screen. This is an alpha with
    rough edges; the install guide covers flashing from the
    browser or with esptool, first-boot setup and recovery.

Filament systems

  • ACE shows a toolchange as it happens (#1678) - the path draws the outgoing lane
    retracting until the hub clears, then the lane being loaded.
  • A CFS box that is switched off shows as Not connected (#1464) - its card is dimmed, its
    bays are left out of counts and lane choices, and tool changes and Clear Spool refuse them.

Other

  • The widget catalog says why a widget will not fit - a widget with no free space on the
    page shows how much room it needs instead of failing when you tap it.
  • Pressed feedback on more rows, chips, value fields, camera source rows and filament
    temperature rows (#1297).

Fixed

Filament systems

  • CFS chains keep each bay's state when a box drops out (#1464) - bays are numbered the way
    the firmware numbers them, so a Klipper restart with one box off no longer shifts spools and
    colours onto the wrong bays, and a box behind a switched-off one still works.
  • CFS and QIDI Box chains draw one toolhead in the filament overview, since every box feeds
    the same extruder.
  • QIDI Box follows live updates - after startup, changes on the box never reached the
    screen.
  • ACE reads the right slots, and French "Currently Loaded" no longer shows garbled
    characters (#1678).
  • Snapmaker U1 tool changer state survives a temperature update, and a malformed slot colour
    leaves the slot's colour alone.
  • A gate sensor that flickers raises one "Same spool?" notice, not a stack of them.
  • AFC and Happy Hare show the right Spoolman vendor right after a spool is relinked.
  • A loaded black or grey spool shows on the nozzle instead of the bare metal tip.

Printing

  • Temperature changes during an AD5X print start no longer fail - a temperature, fan or
    light change during the start macro's bed mesh is sent once the macro finishes instead of
    timing out with "Failed to set temperature", and a jog in that window is refused instead of
    queued for minutes.
  • The bed mesh countdown moves - during the pre-print bed mesh the time left no longer sits
    at a few seconds for minutes on end.
  • Pre-print timing history is kept when a new start is recorded, instead of losing or
    duplicating earlier entries.
  • Park and the Bed tab lift never drive into the plate when the printer reports a Z move
    before confirming it.
  • Action prompts behave like Mainsail's - closing one on screen ends it on the printer, each
    button group gets its own row, and secondary buttons use the secondary colour.
  • Belt Tension and input shaper refuse to start with too little free memory (#1738), which
    could wedge Klipper on the CC1. When Klipper stalls, the message says to power-cycle.

USB sticks

  • A USB print prints the file you picked - Moonraker used to receive only the file name, so
    a print found the file only if a same-named one was already on the printer.
  • USB file details load from the stick - preview, pre-print checks and thumbnails read the
    file in place instead of waiting out a timeout, Cura's JPEG thumbnails show, and listing the
    stick no longer freezes the screen.

G-code preview

  • Two printers with a same-named file no longer share a preview, and a preview whose size
    no longer matches the file on the printer is fetched again.
  • Closing and reopening the print status screen mid-download joins the running download
    instead of starting a second one into the same file.
  • The 3D preview uses the theme colour for a file with no colour information, matching 2D,
    instead of a rainbow height gradient, and filament colours survive switching to 3D while
    printing.
  • The Building preview label shows real progress and is translated; the loading spinner
    shows while a 3D switch builds.

Touch and display

  • Touch calibration on a rotated screen (#1714) - cancelling or retrying no longer
    reinstalls an old touch range, and the preview uses the range it just solved.
  • Panels whose touch range looks swapped correct themselves (Waveshare 2.8in DSI and
    similar) from the first touch past the screen edge, and stay correct on a rotated screen.
  • Screens rotated by the kernel get touch right on first boot (#1428).
  • No crash at startup with background blur on some Allwinner boards (#1742) - blur reuses
    the display's graphics context instead of loading the driver a second time.
  • K2: the camera stays available (#1670) when the stock camera app starts late.

Look and theme

  • Colours set in a screen's layout survive a theme or dark/light switch (#1735).
  • Light mode text is readable on Motion's selected tab, the jog pad and the bed mesh labels.
  • Print file cards fit under the Recently Printed banner instead of clipping the bottom row.
  • Stacked confirm dialogs keep their own buttons and text instead of taking the top one's.
  • A grey picked in a Spoolman colour picker is saved instead of reading as no colour.

Bluetooth and accessories

  • Bluetooth scans - starting a new scan no longer crashes the settings screens or waits out
    the old one, a scan that could not run says so instead of "0 found", and pairing works on
    systems whose adapter is not hci0.
  • Barcode scanners with a generic name are listed, and opening the scanner screen no longer
    freezes it for up to 5 seconds.
  • A USB label printer with an unreadable ID no longer crashes the app.

Stability

  • Raspberry Pi OS 32-bit: no crash when a screen deletes itself (#1601) - the 32-bit stack
    layout made an internal safety check fail.
  • Raspberry Pi OS 32-bit no longer crashes with heap corruption (#1732) - pi32 builds carry
    their own C++ runtime, about 1 MB more.
  • A crash on a background thread leaves a crash report, where before the app exited with
    nothing recorded.
  • A G-code command, file name or network name with invalid characters no longer leaves a
    request hanging (#1493).
  • Rare crashes fixed when switching printers, closing screens with animations off, closing
    the G-code viewer while it loads, starting a sound at startup, and when Moonraker, history and
    Spoolman replies arrive after a screen is gone.
  • The file list no longer floods slow printers with rescans - one metadata scan runs at a
    time, and a file that keeps failing waits before it is tried again.

Other

  • Error messages and toasts from the printer connection are translated, including Wi-Fi
    failures.
  • Connection restored is a success toast and no longer adds a second row to the bell.
  • Cartographer and Beacon probes are found as one probe, and the probe's state shows; K1,
    K2 and QIDI printers keep their probe Z offset live.
  • Editing a setting that appears twice in printer.cfg changes the copy Klipper actually
    reads.
  • Debug bundles redact anything they cannot check before upload.
  • Installer (#1534, #1693) - a vendor screen or KIAUH service that re-enables itself stays
    off, and installing from a desktop session no longer takes down your desktop.

Changed

  • Less memory - Motion, temperature graph, theme editor, calibration, PID, Z offset, touch
    calibration, printer manager, LED and filament system screens free their memory when you
    close them. The print file list loads on first open instead of at startup, and bed mesh
    holds 0.75 to 1.5 MB less.
  • Screens open with one redraw - a settings or overlay screen used to redraw the whole
    display once before it appeared and again as it slid in. It is now built off screen, which
    saves a full-screen draw on every open on slower printers.
  • Updates, crash reports and debug bundles verify the server's certificate - every release
    package ships its own certificate bundle, so printers with outdated system certificates
    still connect. Printers and other devices on your network are unaffected.
  • Settings from releases before 0.99.4 start fresh - the setup wizard runs again, your
    printer connection is kept, and the old file is saved as settings.json.pre-migration.

Don't miss a new helixscreen release

NewReleases is sending notifications on new releases.