v1.1.0-beta.2
The second beta of 1.1. It adds the Motion screen's Move tab, filament drying on the
heated bed and with a chamber heater, live status on the home screen's printer picture,
and a rebuilt LEDs screen. Settings is reorganized so every page is one tap from the
Settings screen. It also fixes a K2 crash at print start and a long list of filament
system problems, most of them on Happy Hare and the Snapmaker U1.
Upgrading from beta.1?
- Settings pages moved; your settings did not. Nothing is reset. Display & Sound
splits into Display, Appearance, Sound and Language & Time, Hardware & Devices becomes
Devices, Safety & Notifications becomes Safety & Alerts, Network and Printers move to
a new Connection page, and Update Channel and Check for Updates move to a new Updates
page. The table under Changed has the full map. - Print Completion Alert now uses its documented default. A printer that never
changed the setting showed only the short notification; it now shows the full-screen
summary. A choice you made yourself is kept. - Material Temperatures changes move to
user_filaments.json. They are moved over
automatically on the first start. Going back to 1.0 or beta.1 loses them, because
those builds read them fromsettings.json, so note them down first if you might go
back. - AD5X and K1 series: touch works again. beta.1 did not respond to touch at all on
these printers; update over SSH or the web interface if the screen is unusable. - "Home printer first?" is gone. A filament load or unload on an unhomed printer
homes and carries on, without asking.
Added
Motion
- Jog and Move tabs (#865) - the Motion screen opens on Jog every time, with the
position readout in the header on both tabs. The Move tab sends the toolhead to nine
named positions laid out like the bed seen from above, placed on the print plate from
your[bed_mesh]area so none aims at a purge area or tool dock. The positions grey
out while the toolhead is moving, and the whole tab is disabled during a print. - Park - runs your printer's own parking macro when it has one, otherwise lifts the
nozzle 10mm and parks over the rear of the plate. Point it at a different macro in
Settings > Printing > Macro Buttons. - Tap a coordinate to move there - a number pad opens for that axis, refuses a value
outside the printer's range, and homes first when needed. A Target / Actual chip beside
the coordinates switches which position is shown. - Hold to repeat on the jog pad and Z buttons, and jog limits you can see: a
button greys out at its limit, and a press that cannot move says which limit it hit.
Drying filament
- Dry filament on the heated bed (#1730) - on an enclosed printer, Dry Filament on
the bed card or in Advanced unloads the toolhead, homes, moves the plate as far from
the nozzle as it goes, and asks you to lay the spools on it under a box. A banner shows
each step as it runs, and Stop leaves the plate where it is. The bed holds a drying
temperature for the material, capped at 90°C, for 12 hours, and HelixScreen will not
home, move or start a print until you confirm the spools are off. Printers you enclosed
yourself can be marked enclosed in Settings > Printing. - Dry filament with a Panda Breath (#1299) - on stock firmware, the chamber card runs
the unit's drying cycle from a material preset, with the live temperature, the time
left and a Stop button, and an optional 70°C bed assist that turns itself off however
the run ends.
Home screen
- The printer picture shows what the printer is doing (#1397) - temperature chips
appear while a heater is on or still hot, and the part fan and light show when they
run. Tap a chip for that heater's graph, the fan controls or the light controls. On
the 13 most common printers each chip points at its part; on others, including your
own photo, Tag parts in the image picker lets you place them. - One LEDs screen for every light (#1130) - a tab per light, with a dot showing
whether it is on and in what color, and each tab shows only what that light can do.
Each home light button controls one light or all of them, chosen from the gear in edit
mode, and Automatic LED Control has its own "Applies to" list.
Filament systems
- Happy Hare: tell the MMU what is really loaded - Recover opens Recover State: pick
the gate that is really selected (or Bypass) and whether filament is loaded, or let
Happy Hare detect it. Nothing moves and no tool is remapped. The slot menu gains
Preload, Maintenance gains Load Extruder and Unload Extruder, and Accessories gains
Refresh Spoolman. - OpenAMS pressure sensor on the filament path (#1724) - OpenAMS without AFC shows
each unit's FPS as a box on the path; tap it for the current pressure.
Everywhere
- Pinch to zoom the 3D views - on a capacitive screen, pinching zooms the 3D G-code
preview and the 3D bed mesh, and a two-finger drag moves the zoomed view.
Changed
-
Settings is twelve pages in three groups (#1023) - Screen, Printer and
HelixScreen, every page one tap from the Settings screen, several with a short status
line such as your brightness or whether an update is waiting.Was Now Display & Sound Display, Appearance, Sound, Language & Time Printing > Toolhead Style, G-code Preview, Z Movement Appearance Hardware & Devices Devices Hardware & Devices > Printers Connection > Printers Safety & Notifications Safety & Alerts Safety & Notifications > Allow cold load/unload, Cool nozzle after filament ops Printing System > Network Settings, Host Connection System > Touch & Input Touch & Input, on the Settings screen Display & Sound > Scroll Buttons, System Keyboard, Keep Navigation Bar Touch & Input Help & About > About > Update Channel, Check for Updates Updates -
Filament operations on an unhomed printer home without asking - the "Home printer
first?" dialog is gone. On the Snapmaker U1, which homes and heats for its own loads,
HelixScreen no longer sends a home or a preheat first, and the load step bar follows
the printer's own order (Home, Select, Feed, Heat, Extrude, Purge), showing Heating and
Purging on those steps. -
Material types and your Material Temperatures changes live in one editable file -
the built-in materials ship in the filament catalog, and your changes move to
user_filaments.json, which you can edit from Mainsail or Fluidd to change a material
or add your own. -
The Controls panel fits small screens - Calibration & Tools holds only calibration,
Motors Off sits beside Motion, and the Light becomes a Quick Actions choice. Advanced
also gains a Pressure Advance row (#1452) and hides sections that are empty on your
printer. -
The log records more by default - production builds log at Info and write each line
as it happens, so a log from a problem you just hit already holds what happened.
Fixed
Crashes
- AD5X, K1, K1C and K1 Max: the touchscreen did not respond - beta.1's build for these
printers read touch events in the wrong size, so every tap was lost. Touch works as in
1.0 again, and a barcode scanner on USB is read correctly too. - K2: the screen crashed and restarted during print start - matching the printer's
start-sequence messages could run out of the small stack these printers give each
thread, with no crash report. K1, AD5X and Creator 5 Pro builds had the same limit. - Raspberry Pi 3 and older: a large G-code preview could freeze the screen - the 3D
preview now limits its detail to what the GPU can draw, and a file too big for that
shows in 2D.
Filament systems
- Happy Hare: a fault often showed no recovery popup (#1323) - a fault during a print,
or a failed load or home outside one, now always opens the popup with Happy Hare's own
reason. Outside a print it leads with Recover instead of Resume. Turning the MMU motors
on no longer homes the MMU. - Snapmaker U1: Unload could be unavailable, or the screen stuck on Unloading - a head
fed to the nozzle by purging can be unloaded, picking a tool no longer reads as loaded,
and an unload that settles straight into its resting state, or one left over from
before a restart, ends properly. - Snapmaker U1: bed drying stopped with "No unload macro found" - the drying flow now
unloads through the filament system, the same way the Unload button does. - Filament stuck in the toolhead with no slot claiming it could not be unloaded
(#1324) - on the AD5X and other systems that can tell, the sidebar and Filament panel
Unload pull it from the active head, and a slot's own Unload greys out in that state. - Stock CFS asked "Same spool?" for a re-inserted spool (#1710) - a tag that reads back
the same values is recognised as the same spool. On AFC, a lane record from an older
plugin build no longer replaces a spool edit you made. - A second filament system's slots showed the first system's materials.
- The heat-first warning checked the wrong slot - Load and Unload check the slot you
selected, and Purge, Extrude and Retract the loaded one. - The MMU's selector, buffer and bypass boxes ignored taps right after the screen
opened. - Device operation messages said "AFC" on every filament system - homing, recovering
and aborting now read the same on all of them. - The Change Filament spool picker could not tell two spools of one vendor apart - each
row now carries Spoolman's filament name.
Screens and files
- Fan and light controls could show frozen dials after being opened from two
different places. Every entry point now opens the same live screen. - Scroll Guard had no effect - with the post-scroll click guard turned on, a tap right
after a scroll still went through. It works again, on the printer's touchscreen, and
needs a restart after changing it. - The number keypad was cramped on 480x320 and 480x272 screens.
- .gcode.3mf files lost their thumbnail and layer height in the file details (#1713),
and print history showed untranslated job states and missing thumbnails for files in
subfolders. - Mainsail kept showing the old version after an update (#1727) - the first start
after an update asks Moonraker to refresh it.