SLOOP 3.4.1 · public beta
⚠ SLOOP 3 is a public beta. Expect bugs, keep backups, and don't rely on it on stage yet. Please report what you find.
Prefer the tried and tested version? SLOOP 2.8 stays in its own repository, github.com/isod89/sloop-fm1.
Install or update
Open isod89.github.io/sloop3-fm1 in Chrome or Edge (or download installer-sloop3-3.4.1.html below). Already on SLOOP 3: steps 3 to 5, about a minute. Back up first: web editor → Projects → BACK UP EVERYTHING.
Reliability: the random freezes
Several of you reported the FM-1 freezing at random. We went looking with new tests that check what the PC simulation couldn't see before, and found two causes:
- A freeze while saving with a heavy project. When the sound uses all the CPU, SLOOP 3 shows CPU OVERLOAD: VOICES CUT. That message could be shown in the middle of a save, at the exact moment the flash memory is busy and the code that draws the message can't be read. The FM-1 then froze or restarted. The message now waits until the save step is over.
- The interrupts' stack. The firmware never set up its own stack for interrupts, so they used the bootloader's, which sits in memory SLOOP 3 reuses for audio buffers. Depending on the bootloader version, this could corrupt memory at random. Interrupts now have their own stack.
Also:
- A flash that stops answering no longer freezes the screen. If an erase or a write never finishes (FM-1s ship with different flash chips), the screen and buttons used to stay dead while the sound went on. After 2 seconds the chip is reset, the save fails cleanly and the previous copy is kept.
- REC armed + SAVE. With REC armed while stopped (REC READY), SAVE → PROJECT → KNOB 1 changed the loop length instead of saving. The REC screen now only shows on the page you armed it from.
If your FM-1 still freezes or restarts, the start screen shows FROZE IN … or RESTART IN … next time. Please put that exact message in your report: it tells us where it happened.
Every sound at the same loudness
- All 156 sounds were re-levelled the way you hear them: with their effects and sends, on three octaves, weighted like the ear (ITU BS.1770). Some were up to 12 dB too loud (CELLO BOW, SOUL OOH, HARMONICA) or 13 dB too quiet (CHIP NOISE, CHOP 8, BREAK 16). They're now all within about half a dB of each other. Projects you already saved keep their levels; a sound you pick again gets the new one.
- The 32 synthesised drum kits are even from one kit to the next. The snare varied by 16 dB between kits (much quieter in 808, LO-FI, VINTAGE, MINIMAL, LATIN, AFRO…), the clap and hats by 6 to 10 dB. Each kit's sounds are now within 1.5 dB of the same sound in the other kits. Kicks are unchanged.
Also in this release (finished after 3.4.0 went out)
- Saving while it plays no longer cuts the sound. Each save goes where the flash is already erased.
- Louder drum kits: every kit about 3 times as loud, the sampled kits as loud as the synthesised ones, the kicks a little more; a new project starts with all 5 tracks at 45. Older projects sound as they did.
- A MIDI file played softly is brought up to NORM when you import it in the editor.
Under the hood
- The PC twin now stops whenever code that lives in the flash runs while the flash is busy, and flags any moment where the screen stops for 3 seconds while the sound goes on. It can also simulate a slow flash chip and a heavily loaded CPU. Long random sessions under those conditions now pass.
- Every build checks the worst-case depth of each stack (main, interrupts, second core) against its size.
Files
| File | What |
|---|---|
installer-sloop3-3.4.1.html
| the installer page, the firmware inside (open it in Chrome or Edge) |
editor-sloop3.html
| the web editor (Chrome or Edge, with SLOOP 3 running on the FM-1) |
sloop3-3.4.1.area
| the plain application area, for developers |
The guide: docs/GUIDE.md. SLOOP 3 is free software (GPL-3.0), unofficial (not made, endorsed or supported by M-VAVE), and installed at your own risk.