emsesp/EMS-ESP32 latest

Development Build v3.9.0-dev.18

on GitHub

[3.9.0]

This release is based on the latest Espressif/Arduino core version 3. It brings in many memory and performance optimizations.

Added

• user-requested LED blink #3063
• Commands Service that can be called via MQTT or API or used in the Scheduler Service
• option to disable factory reset #3150
• TLS support with 4MB boards without PSRAM
• added eth_10mbit to Network Settings, which forces 10BASE-T half-duplex & autonegotiation off, halving the PHY’s power draw. It’s off by default as it will cause issues on managed switches with a port forced to 100Mb #3213
• cleaner MD5 and firmware uploading in WebUI #3222
• pc0Flow in l/min #3224
• remove HA config for excluded entities #3229
• show system reports the Ethernet status on boards with a PHY, so a failed initialisation or a link that never came up is visible instead of Ethernet being omitted completely. Also shows the loop task's lowest free stack, to help diagnose reboots
• new Application Setting "Automatically check for firmware updates", off by default. When enabled EMS-ESP asks emsesp.org for the latest version once a day on its own, otherwise it only asks when the WebUI wants to show it, so an unattended system never contacts emsesp.org
• Automatically check and convert older 3.8.x filesystem to the new 3.9.0 format
• heatpump pool: poolon (switch, 0x48A), hppoolon (pool heating active, 0x488), MP100 poolshuntset (0x5C4) and poolrequest (0x5BA), shorter pool names
• EMS-ESP Recovery, a small firmware for the factory (boot) partition on 16MB boards. It starts a <AP name>-recovery access point and connects to the network with the saved EMS-ESP settings (Ethernet if configured, otherwise WiFi, using the static IP if one is set), and has a WebUI to sign in with an existing admin user, upload a new firmware into either OTA partition, or start one of the installed firmwares. It only reads the EMS-ESP settings, never changes them. Released as EMS-ESP-Recovery-<version>-<chip>-16MB[+].bin, and installed by uploading it in the EMS-ESP WebUI like a normal firmware, or flashed with pio run -e recovery_s3_16M_P -t upload
• firmware rollback: a newly installed firmware is only kept once it has run for 2 minutes. If it crashes or restarts before then, the device goes back to the previous firmware, or to the Recovery if there is none
• on 16MB boards with the Recovery installed, EMS-ESP switches to it after crashing 5 times in a row. The Recovery shows why it was started and which firmware failed to start
• the Version page shows the installed Recovery version on 16MB boards
• crash test builds to try out the rollback and recovery, see [env:crashtest_s3_16M_P] in platformio.ini
• s_16M_P_custom PlatformIO env that HybridCompiles Arduino/IDF with a trimmed sdkconfig (no Bluetooth, PPP/modem, IP forward/NAPT, ULP, SPI Ethernet, GDBSTUB, FreeRTOS trace, mDNS browse/CLI) and places the UART ISR in IRAM
• 16MB builds use EMS-ESP's own Arduino/IDF libs from esp32-arduino-lib-builder instead of Tasmota's prebuilt cores
• optional ccache wrapping when it is installed (scripts/enable_ccache.py) to speed up CI
• heat pump dhw/disinfectduration, the time allowed to reach the thermal disinfection temperature (0xEA offset 15, 120-240 min) #3278

Fixed

• shunting yard show json
• system/sendmail called from a Command or the Scheduler computed its value twice, which stripped the quotes from literal text and then failed on characters like !. Also shunting yard treated a ? inside a quoted string as a ternary, so text like "too hot?" returned nothing
• memory leak when using different timezones for ems-esp and thermostat#3184
• LED stayed off on a healthy system when "Disable LED" was unchecked
• Ethernet MAC address changed with the new SDK, breaking DHCP reservations (currently disabled)
• "IPv4 nameserver" showed an IPv6 address when IPv6 was in use
• the Network status page showed at most one IPv6 address and could hide the IPv4 DNS server entirely. It only read the link-local address, so a dual-stack host's ULA and global addresses were never reported, and it only read two of the three DNS slots, which are shared between IPv4 and IPv6. It now lists every address the interface holds, each labelled with its IPv6 scope, and every configured DNS server #3246
• the Gateway was only ever reported for IPv4, so on a dual-stack network the IPv6 default router was missing from the Network status page, show system and the MQTT info topic. Routers are learnt from router advertisements rather than configured, so all of them are now listed #3246
• show system had the same gaps, reporting a link-local IPv6 address only and a single IPv4 DNS server. The WiFi and Ethernet sections now list every IPv6 address with its scope, and every DNS server labelled with its own family #3246
• the Access Point status page reported whichever interface happened to be active, so with the AP down it showed the station's IP and MAC address under an "Inactive" heading. It now always reports the soft-AP's own details, and shows none when the AP isn't running
• the MQTT info topic published no addresses at all when connected over Ethernet, and over WiFi only an IPv4 address plus a link-local IPv6 one. Both interfaces now report their MAC, IPv4 address and gateway, every IPv6 address and every DNS server. Note that IPv6 address is now an array, and IPv4 DNS Server is replaced by a DNS Server array that covers both families #3246
• HA Discovery warning on Uptime after EMS-ESP boot due to NTP not ready
• hc/control setting for UI800 thermostats #3181
• solar module switches #3223
• UI800/HMI800.2 thermostats without telegram 0x470 reported summertemp as 0 and lost the per-hc heat/cool delays. summermode is now also shown for UI800 heatpumps #3257
• possible crash when the WebUI asked for version information while the versions.json refresh was rewriting the cache from the main loop task
• HTTP client could write past a fixed 64 byte buffer when a URL had a hostname of 64 characters or more, could busy-spin for the whole read budget if the socket reported bytes it wouldn't return, and buffered responses without any size limit
• the "Ethernet clock mode (GPIO16/17) conflicts with PSRAM" error was never logged because Ethernet had already been skipped by the time the check ran
• heat limit entities (maxheatcomp, maxheatheat, dhw.maxheat) read as unknown on heat pumps with an auxiliary heater larger than 9 kW - enum_maxHeat was missing the 12 kW and 15 kW steps
• add 0kW to heat limits #3262, #3265
• show temperature value for sensor 0x40 #3272
• no EMS bus on custom boards whose interface relies on a pull-up on the Rx line. The newer ESP-IDF no longer enables the internal pull-up on the UART Rx pin, so it is now set explicitly as it was in 3.8 #3258
• Guru Meditation (cache error) on HybridCompile builds when the EMS or console UART ISR ran from flash during a SPI flash read (WiFi power-down, mDNS, NVS). The UART ISR and ringbuf ISR helpers are now in IRAM
• compile errors against Arduino 3.3.12 from Tasmota/Arduino headers named console.h, network.h and httpClient.h. Those EMS-ESP headers are now emsesp_console.h, emsesp_network.h and emsesp_http_client.h
• HTTP OTA from WSL/mDNS stalled on IPv6 and used tiny write chunks. Uploads now resolve IPv4 and stream in 64 KB blocks (scripts/upload.py, scripts/upload_cli.py)

Changed

• various memory optimizations #3083
• Scheduler name is now mandatory
• network fallback to AP only after start #3090
• replaced Web async-validator with custom validator and toast with native snackbar to reduce bundle size
• Gateway and Connect devices are shown in the Devices page, but disabled 3126
• show control setting only for master thermostats (0x10) #3173
• remove devices without entities not listed in 0x07 telegram
• changes to the Dialogs in Dashboard page, removed the run icon in the Commands page. Renamed Execute to Run.
• set None for undefined values in HA val_tpl
• changes in WebUI - remove multiple calls systemInfo endpoint, Vewrsion pages checks for internet connection #3195
• multiple optimization in network, power down WiFi when Ethernet and WiFi nosleep is instant when selected #3213
• TLS buffers (~17KB per HTTPS request) are taken from PSRAM on boards that have it, instead of fragmenting the internal heap
• failed versions.json fetches back off from 5 up to 160 minutes instead of retrying every 5 minutes, as each attempt blocks the main loop for as long as the DNS, connect and read timeouts allow
• optimized the LED library to support WS2812B V5 and the newer V6 RGB LEDs
• hold Tx while a K30RF/KM200 gateway is syncing #3094
• Tasmota platform 2026.05.50 (Arduino 3.3.8 / IDF 5.5.4) to 2026.09.50 (Arduino 3.3.12 / IDF 5.5.5). Building that platform needs PlatformIO Core ≥6.2.0; install pioarduino==6.2.0 (official platformio is still 6.1.19). See CONTRIBUTING.md
• CI dev-release firmware jobs run in parallel (webUI, firmware targets, standalone) instead of one serial job

• 5ae89714c chore: update generated files for v3.9.0-dev.18 (proddy)
• f9c9496c7 Merge pull request #3281 from proddy/dev (Proddy)