github cvhviz/CAIRN cairn-v138
Cairn 138 beta

pre-releaseone hour ago

Beta: install it by hand. Radios on Cairn 137 and earlier only look for stable releases, so they aren't offered this one; install it over USB or from the files below. From 138 on, Settings › Firmware update › Beta updates offers the next betas over Wi-Fi.

Cairn 138 rebuilds the Heltec V4 touch keyboard and adds word correction, lets the Cairn app browse and fill the SD card, adds a beta update channel, and redesigns Chats.

Highlights:

  • Heltec V4 touch: a keyboard you can type on (Expansion Kit V2 and Kit V1). It is now always the landscape keyboard, full height with 48 px rows and no status bar while you type; held in portrait, the screen turns while you type and back after. Taps near a key's edge type the nearest key instead of nothing, fast two-thumb typing no longer drops or swaps letters (a space typed fast was coming out as a letter), and repeated deletes stick to Delete. The touch chip is now set up as other drivers do, which roughly halved how far taps read from where you touch.
  • Word correction (Heltec V4 touch and L2 Pro). When a word ends (space or . , ? !), the keys you hit pick the likeliest common word: "tbe" becomes "the", "dont" becomes "don't", "im" becomes "I'm". Delete straight after puts back what you typed. Names (a capital mid-sentence), mIxEd case and anything with a digit are left alone.
  • The SD card in the Cairn app. The app can list the whole card over Bluetooth, and send photos and files to it, or fetch them, over Wi-Fi, including straight into the card's top folder. A phone you "Always allow" starts a transfer without the prompt. Home shows the card's state, and the app can set up a new card's folders. Needs the Cairn app 1.6 (3).
  • Beta updates. Settings › Firmware update › Beta updates offers test builds like this one before they're released. Turn it off and the radio stays on its beta until a newer stable release.
  • Chats, redesigned. Rows in iOS-style groups, a capsule header with New message and New channel easy to see, and a Sort control on the same row (as a sheet).
  • Trip. The elevation line has detail (heights, grade colours, the high point). The page is titled Today when nothing is recording: it always counts the day while the GPS is on. Record trip saves a route to the card; Today › Reset clears only the day's totals. The Cairn app now sees today's trip too.
  • Touch feels quicker. A tap's frame goes out at once, and saving to flash waits while you're using the screen.
  • More: the Beacon screensaver grows into a status card; Display › Rotate on the Heltec touch boards; a hold is the confirm (no dialog after it) for Hibernate, Clear chats, Factory reset and the like, and Restart is now Power; the radio shows up in the app's On This Network list over Wi-Fi, even with App link off; a compact Storage card.

Changed

  • Heltec V4 touch keyboard, word correction, the SD card in the app, Beta updates, Chats, Trip, touch (see above).
  • MeshCore fixes brought in: local network discovery over mDNS, a CLI option for a custom Bluetooth name, CLI reply-buffer overflows fixed, packets whose LoRa header says no CRC dropped, duplicate counters saturate instead of wrapping, and scope 0 rule fixes.

Checked: built from one tree for every board. Each file was checked for the build number and date, and the release has the same set of files as 137. On the bench: the Heltec V4 touch keyboard (logged taps and two typing sessions), the L2 Pro, the ThinkNode M9 and the T-Deck Plus. Word correction was checked in the simulator on both boards and on the Heltec; on the L2 Pro only in the simulator. The SD card browser was used from the Cairn app with an L2 Pro. Every board's screens were checked in the simulator. The L1 family, the one-button boards, the repeaters and the T-Display SF32 are rebuilt from the same tree.

Update

  • On Cairn 108 to 137 (L2 Pro, Heltec V4 touch on either kit, ThinkNode M9, T-Deck, T-Display SF32, T-LoRa Pager): Settings › System › Firmware update: Check, Download, Install. The new build starts on trial and goes back to the old one by itself if it fails to start. On the T-Display SF32, dock the core on the keyboard board first (it carries the Wi-Fi chip).
  • T-Deck started from an SD-card launcher: don't use Update on 121 or earlier (122 and later are fine). Copy MeshCore-TDeckPlus-Cairn138-2026-11-20-update.bin to the card and install it from the launcher, as you installed Cairn.
  • Over USB on an ESP32 board: the -full.bin goes at 0x0, after Erase Flash, and erases everything. The -update.bin goes at 0x10000 and keeps your data. If the board last updated over Wi-Fi, clear the boot selector first, as in the ESP32 install guide.
  • Heltec Wireless Tracker V2 and V4-R8 (OLED) companions: update with the -ble-update.bin at 0x10000; these two don't update over Wi-Fi. A first install is the -ble-full.bin at 0x0 after an erase (back up your node's private key from the app first if the board runs MeshCore or Meshtastic now). Files with -repeater in the name are the repeater, not the companion.
  • Wio Tracker L1 Pro, DV1, L1 e-ink, the room server, the T096 and the T114: double-tap Reset and copy the board's .uf2 onto the drive that appears (UF2 guide), or use the Cairn app's Firmware Update over Bluetooth. Updating keeps your identity, contacts, channels and settings.
  • Compact repeaters: write the -repeater-update.bin at 0x10000, or copy the -repeater.uf2. They don't update over Wi-Fi.
  • T-LoRa Pager: pick the file for your radio (it's on the box and the back label). SX1262 units take TLoraPager, LR1121 units take TLoraPagerLR1121; the wrong one runs but has no radio. The online update keeps to the radio you installed.
  • A board without Cairn: write the board's -full.bin (ESP32 install guide), copy the .uf2 (UF2 guide), or run the SF32 installer (SF32 install guide).

Downloads

Board File Use
Seeed Wio Tracker L2 Pro MeshCore-WioL2Pro-Cairn138-2026-11-20-full.bin first install or recovery over USB, at 0x0 (erases everything)
MeshCore-WioL2Pro-Cairn138-2026-11-20-update.bin update over Wi-Fi, or over USB at 0x10000
Heltec V4-R8 + Expansion Kit V2 (touch) MeshCore-HeltecV4Touch-Cairn138-2026-11-20-full.bin first install or recovery over USB, at 0x0 (erases everything)
MeshCore-HeltecV4Touch-Cairn138-2026-11-20-update.bin update over Wi-Fi, or over USB at 0x10000
Heltec V4 + Expansion Kit V1 (touch) MeshCore-HeltecV4KitV1-Cairn138-2026-11-20-full.bin first install or recovery over USB, at 0x0 (erases everything)
MeshCore-HeltecV4KitV1-Cairn138-2026-11-20-update.bin update over Wi-Fi, or over USB at 0x10000
Heltec Wireless Tracker V2 (companion) MeshCore-HeltecTrackerV2-Cairn138-2026-11-20-ble-full.bin first install or recovery over USB, at 0x0 (erases everything)
MeshCore-HeltecTrackerV2-Cairn138-2026-11-20-ble-update.bin update over USB at 0x10000
Heltec WiFi LoRa 32 V4-R8, OLED (companion) MeshCore-HeltecV4R8-Cairn138-2026-11-20-ble-full.bin first install or recovery over USB, at 0x0 (erases everything)
MeshCore-HeltecV4R8-Cairn138-2026-11-20-ble-update.bin update over USB at 0x10000
Elecrow ThinkNode M9 MeshCore-ThinkNodeM9-Cairn138-2026-11-20-full.bin first install or recovery over USB, at 0x0 (erases everything)
MeshCore-ThinkNodeM9-Cairn138-2026-11-20-update.bin update over Wi-Fi, or over USB at 0x10000
Elecrow ThinkNode M9, USB companion MeshCore-ThinkNodeM9-Cairn138-2026-11-20-usb-full.bin the app over the USB cable (and Bluetooth): first install over USB, at 0x0 (erases everything)
MeshCore-ThinkNodeM9-Cairn138-2026-11-20-usb-update.bin over USB at 0x10000, keeps your data. Online update installs the Bluetooth build, so stay on USB by flashing this by hand
LilyGO T-Deck / T-Deck Plus MeshCore-TDeckPlus-Cairn138-2026-11-20-full.bin first install or recovery over USB, at 0x0 (erases everything, and removes a launcher)
MeshCore-TDeckPlus-Cairn138-2026-11-20-update.bin update over Wi-Fi, over USB at 0x10000, or from a launcher's SD card
LilyGO T-LoRa Pager (SX1262, most units) MeshCore-TLoraPager-Cairn138-2026-11-20-full.bin first install or recovery over USB, at 0x0 (erases everything)
MeshCore-TLoraPager-Cairn138-2026-11-20-update.bin update over Wi-Fi, or over USB at 0x10000
LilyGO T-LoRa Pager (LR1121) MeshCore-TLoraPagerLR1121-Cairn138-2026-11-20-full.bin first install or recovery over USB, at 0x0 (erases everything)
MeshCore-TLoraPagerLR1121-Cairn138-2026-11-20-update.bin update over Wi-Fi, or over USB at 0x10000
LilyGO T-Display SF32 + keypad MeshCore-TDisplaySF32-Cairn138-2026-11-20-install.zip install over USB, with the included installer
MeshCore-TDisplaySF32-Cairn138-2026-11-20-update.bin the app image (and its .sha256)
Seeed Wio Tracker L1 Pro MeshCore-WioL1Pro-Cairn138-2026-11-20.uf2 companion, SH1106 OLED
MeshCore-DV1-Cairn138-2026-11-20.uf2 companion, 2.42" SSD1309 OLED on the Grove port
MeshCore-WioL1Eink-Cairn138-2026-11-20.uf2 companion, 2.13" e-ink
MeshCore-WioL1RoomServer-Cairn138-2026-11-20.uf2 room server
Heltec Mesh Node T096 MeshCore-HeltecT096-Cairn138-2026-11-20-ble.uf2 companion (phone app over Bluetooth)
MeshCore-HeltecT096-Cairn138-2026-11-20-usb.uf2 companion (app over USB serial)
Heltec Mesh Node T114 (✅ beta) MeshCore-HeltecT114-Cairn138-2026-11-20-ble.uf2 companion (phone app over Bluetooth), in color

The compact repeater files (-repeater in the name) are rebuilt from the same tree: Heltec T096 and T114 (.uf2), and the Heltec Wireless Tracker, Tracker V2, V2, V3, V4 and V4-R8 (-repeater-full.bin and -repeater-update.bin). Cairn 138 runs on MeshCore 1.18.0, as 118 to 137 did, with MeshCore's later fixes. SHA256SUMS.txt covers every file: shasum -a 256 -c SHA256SUMS.txt.

Not in this release: the experimental boards (what experimental builds are). The Heltec WiFi LoRa 32 V4 (OLED) companion and the V4 in the non-touch Expansion Kit stay on experimental-heltec-v4-137. The GAT562 30S Mesh Kit companion and the Heltec T114 companion pre-release stay on Cairn 131; the Heltec Vision Master T190 and WiFi LoRa 32 V3 companions stay on Cairn 130, and the LilyGO T5 E-Paper S3 Pro and the SenseCAP MeshPager X2 stay on Cairn 127.

Don't miss a new CAIRN release

NewReleases is sending notifications on new releases.