github cvhviz/CAIRN cairn-v136
Cairn 136

latest release: experimental-heltec-v4-136
one hour ago

Cairn 136 fixes the message cursor on the keyboard boards and the clock on the small OLEDs, lets the ThinkNode M9's @ key type an "@", brings the M9 USB companion into the release, and adds a Heltec V4 Expansion Kit build to the V4 pre-release.

Highlights:

  • The cursor stays at the end of your text (T-Deck, T-LoRa Pager, ThinkNode M9). Typing narrow letters like "f" or "j" pushed the cursor a little further right with each one, so after "ffffffffff" it sat well past the text, and long lines wrapped early. Each line is now measured the way it is drawn, so the cursor sits right after the last letter. Reported in #55.
  • AM/PM no longer runs into the date on the one-button boards' Home screen (the Heltec V4 and V4-R8 OLED companions, and any of them where the time and date can't share a line). With a two-digit hour, "10:59 AM" overlapped "Sun Nov 15"; AM/PM now sits on the line below, next to the time zone. Reported in #53.
  • ThinkNode M9: the @ key types "@" while you write a message, so you can type a mention. Everywhere else it still starts a new message.
  • ThinkNode M9 USB companion joins the release. The M9 build with the app over the USB cable (for setting up M9s from a computer without pairing, #52) was a pre-release since 131; it ran on the bench with a strict test client and now ships here, with an -update.bin too. A Bluetooth M9's online update never picks the USB files.
  • Heltec V4 in the non-touch Expansion Kit: a new build in the V4 pre-release reads the kit's BME280 and GXHTC3 sensors (their readings reach the app) and plays message and startup tones on its buzzer; Menu › Settings › Sound turns it off. Not yet run on a kit: please report in #53.

Changed

  • Cursor on the keyboard boards, the M9's @ key, AM/PM on the OLED Home (see above).

Checked: built from one tree for every board, each file checked for the build number and date, and the same set of files as 135 plus the two M9 USB files. The cursor fix was checked in the T-Deck simulator, typing "ffff…", "jjjj…" and a mixed line (the old code shows the drift there, the new one doesn't), and by a new native test. The M9's @ key was checked in the M9 simulator ("ab", @, "x" gives "ab@x"; outside a message it opens New message). The AM/PM placement was checked by measurement for the widest time, date and zone. The touch boards' screens were compared page by page in the simulator before and after this release's other changes, and are unchanged. The L1 family, the repeaters and the T-Display SF32 are rebuilt with no change but the build number.

Update

  • On Cairn 108 to 135 (L2 Pro, Heltec V4 touch on either kit, ThinkNode M9, T-Deck, T-Display SF32, T-LoRa Pager): Settings › System › Firmware update: Check, Download, Install. The new build starts on trial and goes back to the old one by itself if it fails to start. On the T-Display SF32, dock the core on the keyboard board first (it carries the Wi-Fi chip).
  • T-Deck started from an SD-card launcher: don't use Update on 121 or earlier (122 and later are fine). Copy MeshCore-TDeckPlus-Cairn136-2026-11-16-update.bin to the card and install it from the launcher, as you installed Cairn.
  • Over USB on an ESP32 board: the -full.bin goes at 0x0, after Erase Flash, and erases everything. The -update.bin goes at 0x10000 and keeps your data. If the board last updated over Wi-Fi, clear the boot selector first, as in the ESP32 install guide.
  • Heltec Wireless Tracker V2 and V4-R8 (OLED) companions: update with the -ble-update.bin at 0x10000; these two don't update over Wi-Fi. A first install is the -ble-full.bin at 0x0 after an erase (back up your node's private key from the app first if the board runs MeshCore or Meshtastic now). Files with -repeater in the name are the repeater, not the companion.
  • Wio Tracker L1 Pro, DV1, L1 e-ink, the room server, the T096 and the T114: double-tap Reset and copy the board's .uf2 onto the drive that appears (UF2 guide), or use the Cairn app's Firmware Update over Bluetooth. Updating keeps your identity, contacts, channels and settings.
  • Compact repeaters: write the -repeater-update.bin at 0x10000, or copy the -repeater.uf2. They don't update over Wi-Fi.
  • T-LoRa Pager: pick the file for your radio (it's on the box and the back label). SX1262 units take TLoraPager, LR1121 units take TLoraPagerLR1121; the wrong one runs but has no radio. The online update keeps to the radio you installed.
  • A board without Cairn: write the board's -full.bin (ESP32 install guide), copy the .uf2 (UF2 guide), or run the SF32 installer (SF32 install guide).

Downloads

Board File Use
Seeed Wio Tracker L2 Pro MeshCore-WioL2Pro-Cairn136-2026-11-16-full.bin first install or recovery over USB, at 0x0 (erases everything)
MeshCore-WioL2Pro-Cairn136-2026-11-16-update.bin update over Wi-Fi, or over USB at 0x10000
Heltec V4-R8 + Expansion Kit V2 (touch) MeshCore-HeltecV4Touch-Cairn136-2026-11-16-full.bin first install or recovery over USB, at 0x0 (erases everything)
MeshCore-HeltecV4Touch-Cairn136-2026-11-16-update.bin update over Wi-Fi, or over USB at 0x10000
Heltec V4 + Expansion Kit V1 (touch) MeshCore-HeltecV4KitV1-Cairn136-2026-11-16-full.bin first install or recovery over USB, at 0x0 (erases everything)
MeshCore-HeltecV4KitV1-Cairn136-2026-11-16-update.bin update over Wi-Fi, or over USB at 0x10000
Heltec Wireless Tracker V2 (companion) MeshCore-HeltecTrackerV2-Cairn136-2026-11-16-ble-full.bin first install or recovery over USB, at 0x0 (erases everything)
MeshCore-HeltecTrackerV2-Cairn136-2026-11-16-ble-update.bin update over USB at 0x10000
Heltec WiFi LoRa 32 V4-R8, OLED (companion) MeshCore-HeltecV4R8-Cairn136-2026-11-16-ble-full.bin first install or recovery over USB, at 0x0 (erases everything)
MeshCore-HeltecV4R8-Cairn136-2026-11-16-ble-update.bin update over USB at 0x10000
Elecrow ThinkNode M9 MeshCore-ThinkNodeM9-Cairn136-2026-11-16-full.bin first install or recovery over USB, at 0x0 (erases everything)
MeshCore-ThinkNodeM9-Cairn136-2026-11-16-update.bin update over Wi-Fi, or over USB at 0x10000
Elecrow ThinkNode M9, USB companion MeshCore-ThinkNodeM9-Cairn136-2026-11-16-usb-full.bin the app over the USB cable (and Bluetooth): first install over USB, at 0x0 (erases everything)
MeshCore-ThinkNodeM9-Cairn136-2026-11-16-usb-update.bin over USB at 0x10000, keeps your data. Online update installs the Bluetooth build, so stay on USB by flashing this by hand
LilyGO T-Deck / T-Deck Plus MeshCore-TDeckPlus-Cairn136-2026-11-16-full.bin first install or recovery over USB, at 0x0 (erases everything, and removes a launcher)
MeshCore-TDeckPlus-Cairn136-2026-11-16-update.bin update over Wi-Fi, over USB at 0x10000, or from a launcher's SD card
LilyGO T-LoRa Pager (SX1262, most units) MeshCore-TLoraPager-Cairn136-2026-11-16-full.bin first install or recovery over USB, at 0x0 (erases everything)
MeshCore-TLoraPager-Cairn136-2026-11-16-update.bin update over Wi-Fi, or over USB at 0x10000
LilyGO T-LoRa Pager (LR1121) MeshCore-TLoraPagerLR1121-Cairn136-2026-11-16-full.bin first install or recovery over USB, at 0x0 (erases everything)
MeshCore-TLoraPagerLR1121-Cairn136-2026-11-16-update.bin update over Wi-Fi, or over USB at 0x10000
LilyGO T-Display SF32 + keypad MeshCore-TDisplaySF32-Cairn136-2026-11-16-install.zip install over USB, with the included installer
MeshCore-TDisplaySF32-Cairn136-2026-11-16-update.bin the app image (and its .sha256)
Seeed Wio Tracker L1 Pro MeshCore-WioL1Pro-Cairn136-2026-11-16.uf2 companion, SH1106 OLED
MeshCore-DV1-Cairn136-2026-11-16.uf2 companion, 2.42" SSD1309 OLED on the Grove port
MeshCore-WioL1Eink-Cairn136-2026-11-16.uf2 companion, 2.13" e-ink
MeshCore-WioL1RoomServer-Cairn136-2026-11-16.uf2 room server
Heltec Mesh Node T096 MeshCore-HeltecT096-Cairn136-2026-11-16-ble.uf2 companion (phone app over Bluetooth)
MeshCore-HeltecT096-Cairn136-2026-11-16-usb.uf2 companion (app over USB serial)
Heltec Mesh Node T114 (✅ beta) MeshCore-HeltecT114-Cairn136-2026-11-16-ble.uf2 companion (phone app over Bluetooth), in color

The compact repeater files (-repeater in the name) are rebuilt from the same tree: Heltec T096 and T114 (.uf2), and the Heltec Wireless Tracker, Tracker V2, V2, V3, V4 and V4-R8 (-repeater-full.bin and -repeater-update.bin). Cairn 136 runs on MeshCore 1.18.0, as 118 to 135 did. SHA256SUMS.txt covers every file: shasum -a 256 -c SHA256SUMS.txt.

Not in this release: the experimental boards (what experimental builds are). The Heltec WiFi LoRa 32 V4 (OLED) companion moves to experimental-heltec-v4-136, now with a build for the V4 in the non-touch Expansion Kit (its sensors and buzzer) and an -update.bin beside each -full.bin. The GAT562 30S Mesh Kit companion and the Heltec T114 companion pre-release stay on Cairn 131; the Heltec Vision Master T190 and WiFi LoRa 32 V3 companions stay on Cairn 130, and the LilyGO T5 E-Paper S3 Pro and the SenseCAP MeshPager X2 stay on Cairn 127.

Don't miss a new CAIRN release

NewReleases is sending notifications on new releases.