Cairn 109 updates the Wio Tracker L2 Pro, Heltec V4 touch, ThinkNode M9 and T-Deck. The T-Display SF32 stays on Cairn 108; the L1 Pro, T096 and preview boards on Cairn 107.
Highlights:
- T-Deck: sound works, through its speaker: message chimes, tones and a volume setting.
- Offline maps now live in cairn/maps// on the microSD card (they were in l2map/). Move each map folder into cairn/maps/, or build it again with tools/maptiles.py, which now writes there.
- Erase card now labels the card CAIRN.
- New: compact repeater images for the Heltec T096, T114, V2, V3, V4, V4-R8 and Wireless Tracker V1/V2, with a minimal screen, a power save (screen and TX LED off; double-click wakes) and power off (hold on Status, then release).
Update
- On Cairn 108: Settings > System > Firmware update: Check, Download, Install. The new build starts on trial and goes back to 108 by itself if it fails to start. On the T-Deck this is its first update over Wi-Fi.
- Your map card: create a
cairn/mapsfolder at the top of the card and move each set folder froml2map/into it (for examplel2map/okc-topobecomescairn/maps/okc-topo), or rebuild the set with the map tool. Nothing inside the set changes. - A board without Cairn: write the board's
-full.bin(ESP32 install guide).
Downloads
| Board | File | Use |
|---|---|---|
| ✅ Seeed Wio Tracker L2 Pro | MeshCore-WioL2Pro-Cairn109-2026-10-07-full.bin
| first install or recovery over USB, at 0x0
|
MeshCore-WioL2Pro-Cairn109-2026-10-07-update.bin
| update over USB at 0x10000, or over Wi-Fi
| |
| ✅ Heltec V4 + Expansion Kit (touch) | MeshCore-HeltecV4Touch-Cairn109-2026-10-07-full.bin
| first install or recovery over USB, at 0x0
|
MeshCore-HeltecV4Touch-Cairn109-2026-10-07-update.bin
| update over USB at 0x10000, or over Wi-Fi
| |
| ✅ Elecrow ThinkNode M9 (beta) | MeshCore-ThinkNodeM9-Cairn109-2026-10-07-full.bin
| first install or recovery over USB, at 0x0
|
MeshCore-ThinkNodeM9-Cairn109-2026-10-07-update.bin
| update over USB at 0x10000, or over Wi-Fi
| |
| ✅ LilyGO T-Deck / T-Deck Plus (beta) | MeshCore-TDeckPlus-Cairn109-2026-10-07-full.bin
| first install or recovery over USB, at 0x0
|
MeshCore-TDeckPlus-Cairn109-2026-10-07-update.bin
| update over USB at 0x10000, or over Wi-Fi
|
SHA256SUMS.txt covers every file: shasum -a 256 -c SHA256SUMS.txt. The T-Display SF32's files are in Cairn 108; the nRF52840 and preview boards' in Cairn 107.
T-Deck sound
The T-Deck has a MAX98357A speaker amplifier rather than the buzzer the other boards use. Cairn now drives it over I2S with the same tones as the L2 Pro's speaker, and the Sound settings and the quick panel's Sound tile work, with a volume slider. Between tones the amplifier is idle, so it costs nothing while silent.
Map folder
Every board with the Cairn interface reads offline maps from cairn/maps/<name>/ (the same folder the T-Display SF32 interface keeps its files under cairn/). The format inside a set is unchanged: manifest.txt and the .l2t block files. The old l2map/ folder is no longer read.
Compact repeaters
The standard MeshCore repeater (the same mesh, CLI and remote admin) with a minimal Cairn screen on the one button: Status (repeat on/off, channel, packets, neighbours, noise floor, uptime), Spectrum (hold sends an advert) and Settings (Repeat, TX power, Send advert, Power save, Reboot; hold acts, Reboot asks twice). Power save turns the screen and the TX LED off and is kept across reboots; a double-click wakes it. Turning off: hold the button on Status until it says Release to turn off (~3 s), then let go; a press turns it back on. Details: Compact repeater.
| Board | File | Use |
|---|---|---|
| ✅ Heltec Mesh Node T096 (beta) | MeshCore-HeltecT096-Cairn109-2026-10-07-repeater.uf2
| copy onto the board's USB drive |
| 🧪 Heltec T114 | MeshCore-HeltecT114-Cairn109-2026-10-07-repeater.uf2
| copy onto the board's USB drive |
| 🧪 Heltec V2 | MeshCore-HeltecV2-Cairn109-2026-10-07-repeater-full.bin
| first install at 0x0
|
MeshCore-HeltecV2-Cairn109-2026-10-07-repeater-update.bin
| update at 0x10000
| |
| 🧪 Heltec V3 | MeshCore-HeltecV3-Cairn109-2026-10-07-repeater-full.bin
| first install at 0x0
|
MeshCore-HeltecV3-Cairn109-2026-10-07-repeater-update.bin
| update at 0x10000
| |
| 🧪 Heltec V4 | MeshCore-HeltecV4-Cairn109-2026-10-07-repeater-full.bin
| first install at 0x0
|
MeshCore-HeltecV4-Cairn109-2026-10-07-repeater-update.bin
| update at 0x10000
| |
| 🧪 Heltec V4-R8 | MeshCore-HeltecV4R8-Cairn109-2026-10-07-repeater-full.bin
| first install at 0x0
|
MeshCore-HeltecV4R8-Cairn109-2026-10-07-repeater-update.bin
| update at 0x10000
| |
| 🧪 Heltec Wireless Tracker | MeshCore-HeltecTracker-Cairn109-2026-10-07-repeater-full.bin
| first install at 0x0
|
MeshCore-HeltecTracker-Cairn109-2026-10-07-repeater-update.bin
| update at 0x10000
| |
| 🧪 Heltec Wireless Tracker V2 | MeshCore-HeltecTrackerV2-Cairn109-2026-10-07-repeater-full.bin
| first install at 0x0
|
MeshCore-HeltecTrackerV2-Cairn109-2026-10-07-repeater-update.bin
| update at 0x10000
|
✅ beta: run on hardware (the T096). 🧪: built from the same code, not yet tried on that board.
Testing so far
- T-Deck: the speaker driver installed over USB and heard on hardware (message tone and previews).
- All four boards build; the interface's 709 host tests pass, including the card walk and delete paths under
cairn/maps; the map tool's self-test passes, and a set it built incairn/maps/topoverifies. - Not yet seen on a board: a map loading from
cairn/maps. Please report if a map card shows "No maps" after moving its folder. - Compact repeaters: all eight build; the T096 image installed over UF2 and runs (its CLI answers, settings kept; two units updated in place). The Heltec, Tracker and T114 images haven't been tried on hardware.