Cairn 106 is the first Cairn release, and one release now covers all four boards: Wio Tracker L1 Pro, Wio Tracker L2 Pro, Heltec V4 touch and Heltec T096. It is MeshCore v1.17.1 underneath and works with the official MeshCore apps.
Highlights:
- Online updates on the L2 and Heltec V4: the device checks this page once a day on Wi-Fi and installs only when you say so.
- Pinch to zoom on the offline map (L2, Heltec V4).
- Longer battery life with the screen off on the L2 and Heltec V4: slower CPU while dark, calmer Bluetooth advertising, touch and backlight chips asleep, SD card powered down when idle.
- Bluetooth on or off is remembered across restarts.
- The phone app no longer switches GPS Eco to On (all boards).
- Heltec V4: quick taps no longer get lost, and the button wake no longer leaves a blank lit screen.
- L1 Pro: Cairn splash, optional side page tabs, regrouped settings, and a fix for contacts that never synced.
- Heltec T096 joins Cairn with its themed one-button UI.
Updating keeps your identity, contacts, channels and settings.
Downloads
| Board | File | Use |
|---|---|---|
| Wio Tracker L1 Pro | MeshCore-WioL1Pro-Cairn106-2026-10-03.uf2
| companion, SH1106 OLED (main L1 build) |
MeshCore-DV1-Cairn106-2026-10-03.uf2
| companion, 2.42" SSD1309 OLED on the Grove port | |
MeshCore-WioL1Eink-Cairn106-2026-10-03.uf2
| companion, 2.13" e-ink | |
MeshCore-WioL1RoomServer-Cairn106-2026-10-03.uf2
| room server | |
| Wio Tracker L2 Pro | MeshCore-WioL2Pro-Cairn106-2026-10-03-full.bin
| first install or recovery: 0x0 after a full erase
|
MeshCore-WioL2Pro-Cairn106-2026-10-03-update.bin
| update: 0x10000, a browser upload, or the online updater
| |
| Heltec V4 touch | MeshCore-HeltecV4Touch-Cairn106-2026-10-03-full.bin
| first install or recovery: 0x0 after a full erase
|
MeshCore-HeltecV4Touch-Cairn106-2026-10-03-update.bin
| update: 0x10000, a browser upload, or the online updater
| |
| Heltec T096 | MeshCore-HeltecT096-Cairn106-2026-10-03-ble.uf2
| companion over Bluetooth |
MeshCore-HeltecT096-Cairn106-2026-10-03-usb.uf2
| companion over USB serial |
Bluetooth pairing uses the PIN shown on the device's screen: a new random PIN each boot, unless you set your own in Settings.
SHA256SUMS.txt covers every file: shasum -a 256 -c SHA256SUMS.txt. How to flash each board is in the README.
The online updater is new in this release, so an L2 or Heltec V4 on an older build needs one USB or browser update to 106; later releases can then arrive over Wi-Fi.
Wio Tracker L2 Pro and Heltec V4 touch
Online updates. Settings > System > Firmware update > Check for updates. While on Wi-Fi the device also checks once a day (first ~2 min after Wi-Fi connects). A newer build shows a dot on Settings and one notice; the release page shows the notes, size and date, and Install downloads this board's -update.bin over HTTPS with certificate checks, verifies its size, SHA-256 and board marker, then restarts into it. Bluetooth is turned off during the install. Nothing installs without your confirmation, and a failed install leaves the current build in place.
Pinch to zoom on the GPS map: a live scaled preview while you pinch, a "Zoom N" chip, and the map snaps to the nearest zoom level around your fingers when you lift. Other pages ignore a second finger, so two-thumb typing is unaffected.
Battery life with the screen off (estimated, not yet measured): CPU at 80 MHz while dark, the main loop rests when idle, Bluetooth advertises fast for 30 s after boot or a disconnect and then about once a second, the touch controller sleeps while dark when tap-to-wake is off, the L2's backlight chip goes to standby, and the L2's SD card is powered down when idle even with a card inserted. New installs start at 75% brightness.
Bluetooth on/off is remembered across restarts (Wi-Fi already was).
Fixes
- Logging in to a room or repeater from the device while the phone app is logging in to the same node now says "Busy" instead of risking the saved password being overwritten.
- Saved admin and room passwords are written outside the radio receive path.
- The remote-admin airtime limit now also covers retries and "Try flood".
- Very large telemetry values display correctly.
- The Wi-Fi app link asks again when a different device inherits the allowed phone's IP address.
- Heltec V4: quick taps that drifted as the finger lifted were read as drags and did nothing; the tap tolerance is now 24 px on this board.
- Heltec V4: waking with the button while tap-to-wake was off lit a blank screen (the touch reset also resets the display); the display is now set up again after it.
Wio Tracker L1 Pro
- Cairn boot splash on all four images: the stacked-stones mark, the CAIRN wordmark, the build number and a 12-hour build stamp.
- Settings > Page tabs: Bottom or Side. The page icons can stand in a column down the left edge.
- Settings are regrouped to match the touch builds.
- Distances to message senders are in miles, and on-screen text uses American spelling.
- Fixed: contacts added after an anonymous request now sync to the app.
- Fixed:
set afrejects bad values on the room server CLI.
Heltec T096
The themed one-button T096 firmware now builds from the Cairn tree, so it picks up the fork's mesh, storage, radio and app fixes. It gets the Cairn splash, feet and °F, and Cairn's stuck-receiver re-arm plus the T096's own noise-floor re-seed.
All boards
- The phone app's GPS setting keeps Eco mode instead of switching it to On.
- On-device testing so far: L2 and Heltec V4 basic use, pinch to zoom and the Heltec wake fix are confirmed on hardware. The power changes and the online install are new in this release.