RELEASE NOTES

Migration Information

This version removes support for direct migration from versions before v8.1.0 (Doris)

See migration path for instructions how to migrate to a major version.

Do not upgrade from minimal to minimal version. It will most likely fail at some point and will require flashing via serial. If you do have to use minimal versions, always OTA to a full version of the same release before applying next minimal version.

Pay attention to the following version breaks due to dynamic settings updates:

Migrate to Sonoff-Tasmota 3.9.x
Migrate to Sonoff-Tasmota 4.x
Migrate to Sonoff-Tasmota 5.14
Migrate to Sonoff-Tasmota 6.7.1 (http://ota.tasmota.com/tasmota/release_6.7.1/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
Migrate to Tasmota 7.2.0 (http://ota.tasmota.com/tasmota/release-7.2.0/tasmota.bin)

--- Major change in parameter storage layout ---

Migrate to Tasmota 8.5.1 (http://ota.tasmota.com/tasmota/release-8.5.1/tasmota.bin)

--- Major change in internal GPIO function representation ---

Migrate to Tasmota 9.1 (http://ota.tasmota.com/tasmota/release-9.1.0/tasmota.bin.gz)
Upgrade to latest release (http://ota.tasmota.com/tasmota/release/tasmota.bin.gz)

While fallback or downgrading is common practice it was never supported due to Settings additions or changes in newer releases. Starting with release v9.1.0 Imogen the internal GPIO function representation has changed in such a way that fallback is only possible to the latest GPIO configuration before installing v9.1.0.

Supported Core versions

This release will be supported from ESP8266/Arduino library Core version 2.7.4.9 due to reported security and stability issues on previous Core version. This will also support gzipped binaries.

This release will be supported from ESP32/Arduino library Core version 2.0.3.

Support of ESP8266 Core versions before 2.7.4.9 and ESP32 Core versions before 2.0.3 have been removed.

Support of TLS

In addition to TLS using fingerprints now also user supplied CA certs, AWS IoT and Azure IoT is supported. Read full documentation

Initial configuration tools

For initial configuration this release supports Webserver based WifiManager or Serial based command interface.

Initial installation

Easy initial installation of Tasmota can be performed using the Tasmota WebInstaller.

Provided Binary Downloads

ESP8266 or ESP8285 based

The following binary downloads have been compiled with ESP8266/Arduino library core version 2.7.4.9.

tasmota.bin = The Tasmota version with most drivers for 1M+ flash. RECOMMENDED RELEASE BINARY
tasmota4M.bin = The Tasmota version with most drivers and filesystem for 4M+ flash.
tasmota-AF.bin to tasmota-VN.bin = The Tasmota version in different languages for 1M+ flash.
tasmota-lite.bin = The Lite version without most drivers and sensors for 1M+ flash.
tasmota-knx.bin = The Knx version without some features but adds KNX support for 1M+ flash.
tasmota-sensors.bin = The Sensors version adds more useful sensors for 1M+ flash.
tasmota-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 1M+ flash.
tasmota-display.bin = The Display version without Energy Monitoring but adds display support for 1M+ flash.
tasmota-zbbridge.bin = The dedicated Sonoff Zigbee Bridge version for 2M+ flash.
tasmota-zigbee.bin = The dedicated cc25xx Zigbee Bridge version for 4M+ flash.

Above binaries are also available as gzipped version allowing faster uploads.

Latest released binaries can be downloaded from

Historical binaries can be downloaded from

http://ota.tasmota.com/tasmota/release-12.0.1

The latter links can be used for OTA upgrades too like OtaUrl http://ota.tasmota.com/tasmota/release/tasmota.bin.gz

ESP32, ESP32-C3, ESP32-S2 and ESP32-S3 based

The following binary downloads have been compiled with ESP32/Arduino library core version 2.0.3.

tasmota32.bin = The Tasmota version with most drivers including additional sensors and KNX for 4M+ flash. RECOMMENDED RELEASE BINARY
tasmota32xy.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C3/S2/S3 and 4M+ flash.
tasmota32xycdc.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C3/S2/S3 with serial over embedded USB CDC only and 4M+ flash.
tasmota32solo1.bin = The Tasmota version with most drivers including additional sensors and KNX for single core ESP32 and 4M+ flash.
tasmota32-AF.bin to tasmota32-VN.bin = The Tasmota version in different languages for 4M+ flash.
tasmota32-bluetooth.bin = The Bluetooth version adds BLE support for 4M+ flash.
tasmota32-display.bin = The Display version without Energy Monitoring but adds display support for 4M+ flash.
tasmota32-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 4M+ flash.
tasmota32-lvgl.bin = The LVGL version adds Light and Versatile Graphics Library (LVGL) display support for 4M+ flash.
tasmota32-nspanel.bin = The Sonoff NSPanel Smart Scene Wall Switch version with HASPmota display support.
tasmota32-webcam.bin = The Webcam version adds webcam support for 4M+ flash.
tasmota32-zbbridgepro.bin - The Sonoff Zigbee Bridge Pro version with CC2652P firmware load support.

Latest released binaries can be downloaded from

Historical binaries can be downloaded from

http://ota.tasmota.com/tasmota32/release-12.0.1

The latter links can be used for OTA upgrades too like OtaUrl http://ota.tasmota.com/tasmota32/release/tasmota32.bin

Additional information

List of embedded modules.

Complete list of available feature and sensors.

Changelog v12.0.1 Paul

Added

Command SetOption139 0/1 to switch between pressure unit "mmHg" (0) or "inHg" (1) when SO24 1 #15350
Command SetOption140 0/1 to switch between MQTT Clean Session (0) or Persistent Session (1) #15530
Command SetOption141 1 to disable display of module name in GUI header
Command SetOption142 1 to wait 1 second for wifi connection solving some FRITZ!Box modem issues #14985
Command EnergyExportActive<phase> to (p)reset energy export active for supported devices. Currently ADE7880 only #13515
Command IfxRp ""|<policy> adds optional InfluxDb Retention Policy #15513
Command SspmDisplay 2 to display Sonoff SPM energy data in GUI for user tab-selected relay modules #13447
Command SSerialSend9 0/1 to enable Serial Bridge console Tee for debugging purposes
Support for Sonoff MS01 soil moisture sensor #15335
Support for daisy chaining MAX7219 displays #15345
Support for Sensirion SHT4X using define USE_SHT3X #15349
Support for Sonoff SPM v1.2.0
Support for Sonoff Zigbee Bridge Pro by Stephan Hadinger #15701
Support for Sonoff NSPanel Smart Scene Wall Switch
Support for flowrate meters like YF-DN50 and similary #15474
Support for 5-channel light dimmer driver BP5758D used in Tuya bulbs #15713
Support for HYTxxx temperature and humidity sensor #15715
Sonoff SPM delayed SetPowerOnState #13447
ESP32 Command Restart 3 to switch between SafeBoot and Production

Breaking Changed

Changed

Restructured tasmota source directories taking benefit from PlatformIO Core v6.0.2
Prepare to remove dedicated Home Assistant discovery in favour of Tasmota Discovery and hatasmota
ESP32 Tasmota SafeBoot with changed partition scheme allowing larger binaries
ESP32 increase Serial Bridge input buffer from 130 to 520 characters

Fixed

Improv initial or erase device installation failing to provide Configure WiFi option
SCD40 start low power command #15361
BL09xx negative power presentation #15374
Possible pin output toggle after power on #15630
SHT1X driver hangs and wrong values on ESP32 #15790
Resolving NTP and/or MQTT server names regression from v12.0.0 #15816
ESP32 Arduino Core WiFi timeout is changed from msec to seconds

Removed

Arduino IDE support

arendst/Tasmota v12.0.1 Tasmota v12.0.1 Paul on GitHub