Unofficial CachyOS image for PS5. Flash it, boot it, play.
Credit: based on the official ps5-linux CachyOS image and its kernel patches. All credit for the base image, kernel patches, Wi-Fi driver and first-boot setup goes to the ps5-linux project. Report problems with this build here, not to them.
New in this release
- Kernel 7.3.4 with ps5-linux-patches
1472828(wasb33e7c5), fixes from upstream #83:- Bluetooth no longer dies after a while (USB controller fix)
- GPU no longer gets stuck at full clock with boost on
- Power off and reboot no longer hang
- Several driver crashes now fail with an error instead of a kernel panic
- Wi-Fi/Bluetooth chip pairing key fix
- Wi-Fi driver
6e87c85: follows your router's country setting and no longer advertises TDLS - PS5 Slim (VERDE) colour fix: no more yellow/red tint. 12-bit 4:2:2 output is now only used on the FLAVA3 HDMI chip; other consoles keep 8-bit RGB
- "12-bit Colour" icon says it isn't supported on PS5 Slim
- "Update PS5 CachyOS" desktop icon: runs the updater (newest kernel, fixes, extras). A daily check shows a notification when a newer kernel is out
- Quieter fan curve on by default (full speed still at 88 °C), plus a "SoC Temp" reading in the panel (added on the first desktop login). Back to the kernel's default curve:
curl -fsSL https://raw.githubusercontent.com/abrocoma/PS5-CachyOS/main/scripts/quiet-fan.sh | sh -s -- --remove
Display
- 1080p, 1440p up to 144 Hz and 4K at 60 Hz. 4K at 120 Hz needs an HDMI 2.1 TV (untested)
- 1080p and 1440p without black screens (DP link lock)
- HDR on the desktop: off by default, turn it on in System Settings → Display. HDR at 4K needs Colour resolution set to 12 bits (click the "12-bit Colour" desktop icon)
- 12-bit colour, 4:2:2 output to the HDMI bridge
- HDR and 12-bit colour need the FLAVA3 HDMI chip; consoles with the VERDE chip get 8-bit without HDR by default. Check yours with
sudo dmesg | grep "HDMI IC" - Tip: if you use desktop scaling above 100%, set System Settings → Display → Legacy Applications (X11) to "Apply scaling themselves". Otherwise games like CS2 run at a lower resolution and look blurry
Gaming Mode
- SteamOS-style Steam interface on boot
- Starts at your screen's native resolution and up to 144 Hz (60 Hz screens get 60, 120 Hz TVs get 120)
- "Gaming Mode Refresh Rate" desktop icon: choose 144 Hz, 120 Hz (for FreeSync / VRR), 60 Hz or the monitor default
- Display and network settings in Steam
- Switch to Desktop from Steam's power menu, and back with the "Return to Gaming Mode" desktop icon
- No Steam update check hang (OS updates:
sudo pacman -Syu)
Hardware support
- Bluetooth: DualSense reconnects automatically
- Wi-Fi: NXP IW620 driver
6e87c85 - USB: boots from a USB SSD in a rear port or the front USB-C port (
usbc_dp.enable=0, so the USB-C driver can't drop the boot drive) - Quiet fan curve from boot (
ps5-fan-curve.service), GPU slows down at 85 °C
System
- CachyOS packages on Arch Linux, KDE Plasma (the system reports itself as "Arch Linux", like the official image)
- zram swap (half the RAM, zstd)
- Chrome hardware video decode flags
- First-boot setup: timezone, password, hostname, and the partition grows to fill the drive
Flashing
- Windows / macOS: extract the
.img.xzto.imgfirst (7-Zip on Windows, double-click on macOS), then flash the.imgwith balenaEtcher. - Linux:
xzcat ps5-cachyos-7.3.4-p1472.img.xz | sudo dd of=/dev/sdX bs=4M status=progress conv=fsync
Check the download first: sha256sum ps5-cachyos-7.3.4-p1472.img.xz must match ps5-cachyos-7.3.4-p1472.img.xz.sha256.
Known issues
- Drive not found at boot ("waiting for device", then an emergency shell): push the USB cable all the way in and use a rear USB port. If your drive gets stuck when the PS5 hands over to Linux, unplug it and plug it back in while the boot waits, and the boot carries on by itself.
- After a warm restart (kexec): Wi-Fi can fail, and on some USB SSDs writes stay slow (reads are fine). A cold boot from the PS5 fixes both.
- Two PS5 Linux drives plugged in at once: both have a partition labelled
boot, so the system can mount the other drive's one. Keep only one PS5 Linux drive plugged in while updating (the updater now refuses to write to another drive). - Not tested on a PS5 Pro.
Tested on a PS5 (FW 13.60) with soniciso1's ps5-linux-loader, this image on a USB drive: first-boot setup, partition grow, 1440p 144 Hz, Bluetooth/DualSense, Wi-Fi, the quieter fan curve, the SoC Temp reading, and the update notification.
Default login: steam / steam, and SSH is on (the official image's defaults). Change the password in the first-boot setup ("Customize").
Source: see KERNEL-SOURCE.md and the attached linux.patch.