TheUnboundDeveloper/AM-Reaper v3.1.3-beta-RT-BE86U

Reaper v3.1.3-beta — RT-BE86U

on GitHub

v3.1.3 — your Killswitch decides, and the firewall watchdog stops fighting a rule you meant (built RT-BE96U)

• Policy Routing follows each VPN client's Killswitch instead of overriding it. Every rule that
  sent traffic to a VPN client used to add a block beneath it, so if that tunnel dropped the traffic
  stopped - whatever the client's own Killswitch said. That was Reaper deciding something you had
  already decided on the VPN page, and it disagreed with VPN Director on the same router. Now a rule
  only chooses the path; whether a tunnel that is down blocks the traffic or lets it use the WAN is
  that client's Killswitch, exactly as for VPN Director, and it takes effect the moment you change it
  there. This changes behaviour on upgrade: a rule targeting a client whose Killswitch is off
  now falls back to the WAN while the tunnel is down, where it used to block. To keep the old
  protection, turn that client's Killswitch on. The rules table says which applies to each rule
  while its client is off, and the rule is stated once beneath the table.
• The Policy Routing table names the interface, not the consequences. The Target column showed a
  running commentary on every WireGuard row. It now shows the target; a small LAN badge marks the
  one thing worth seeing per row - a destination or device rule that costs the whole LAN its hardware
  acceleration - and a single note beneath the table explains the bypass once.
• Apply on Policy Routing shows that it is working. The button dims the moment it is pressed and
  the overlay stays up until the Keep / Revert bar appears, instead of vanishing for the few seconds
  the rules take to go live and leaving the page looking dead.
• The Administration tab is now called DNS Failover. "Failover" alone reads as Dual-WAN failover;
  the tab holds the DNS resolver health check and the dnsmasq switches, so it now says so.
• The first-boot Wi-Fi page shows its header again on every sibling model. Since v3.1.0 the
  page that greets a new RT-BE86U, RT-BE88U, GT-BE98 or GT-BE98 Pro owner has asked for the
  RT-BE96U's animated header — a file those models deliberately do not carry — so the top of the
  page was a broken image. Nothing else on the page was affected. It slipped through because the
  page arrived after the three places that keep track of which pages show the header were written,
  and none of them was told; every build check they fed was green. They no longer keep a list:
  they ask the source tree, and the build now refuses any image whose pages name a header file
  that is not actually in it. (The RT-BE96U was never affected.)
• The firewall watchdog no longer fights a rule you put ahead of it on purpose. v3.1.2's
  chain-integrity watchdog re-pinned Reaper's front chains to the head of the base chains every
  ten minutes, which was right for an add-on that had shoved them aside and wrong for a narrow
  carve-out — say, a DNS rule that has to beat Gatekeeper so restricted devices keep resolving —
  that has to sit in front. The two would trade places indefinitely, taking DNS away from
  restricted devices for a couple of seconds each round and leaving the watchdog permanently
  red. It now looks at what is ahead of it: a rule that can only affect a narrowed class of
  traffic, or a chain named in /jffs/reaper/front_exempt, is tolerated and logged once; a rule
  that could wave anything through is still repaired. And if a repair is undone twice, it says
  what is happening, names the file that ends it, and stops.
• The diagnostic report stops overstating what it found. reaper_diag is what you send when
  something is wrong, so a figure that reads high sends the next person chasing something that was
  never there. Six of them did. The conntrack section re-read the live table for every line, so the
  printed total and the per-protocol breakdown came from different instants and did not add up —
  405 entries against 510 by protocol — and now every figure comes from one snapshot. The syslog
  section counted the USB mirror and the log it mirrors as two separate logs, inflating every
  count in the section by about 2.2x (12,360 lines where the router had 5,634 distinct), and it
  counted the lab assistant's echo of your own typed commands, which by itself reported two kernel
  panics on a router that had none. "Boots in span" counted syslogd restarts, which any service
  cascade produces without a reboot: 13 boots on a router that had been up for minutes — it now
  reports uptime, the only boot marker this hardware has, and labels the syslogd figure as what it
  really counts. The panic pattern matched the ordinary English word "oops" wherever it appeared.
  "Kernel tainted" printed a bitmask as if it were a count — 4097 is two flags, not four thousand —
  and now names the flags. And RW_FDROP, a chain that by design never exists because
  forward-direction drops share RW_DROP, stopped being reported as missing on every healthy
  router.
• The EDNS Client Subnet switch says what actually leaves the router. It sends the complete
  client address rather than a shortened prefix, and it is attached when a query is received —
  before an upstream is chosen — so it travels with every forwarded query, including any that
  reaches a public fallback server while your own filter is unavailable. The help text now says
  so: turn it on only when the DNS server receiving it is one you run.
• Two things that used to happen silently now say so. Policy Routing treats its confirmed
  snapshot as authoritative, which is right, but it did so without a word: a rule list left in
  nvram was discarded, and an nvram flag saying policy routing was on was overruled by a snapshot
  saying off. An operator could stage a whole configuration and watch it vanish with nothing in
  the log. Each is now logged, and only when the two genuinely disagree. Separately, the
  watchdog's generated script now ends with an explicit success: it had been returning the result
  of whatever ran last — a log-rotation test that is false on any mirror under 8 MB — so a
  perfectly healthy router reported failure to anything that asked, with no fault recorded
  anywhere.
• For maintainers: the build's own test suites now run in CI. They existed and nothing ran
  them, which is how an unbound shell variable killed all six v3.1.2 publish jobs after a green
  build. Every suite under build-scripts/tests/ is discovered by glob, so a new one runs without
  anyone remembering to wire it up; a suite that needs the router source tree, which is not in
  this repo, reports "skipped" rather than failing. A run in which nothing at all executed is
  refused — a green check that proved nothing is worse than a red one.

Images & checksums (RT-BE86U)

Two flashable images: + AI Advisor (default) and Standard (noMCP, all AI components compiled out entirely). Flash the *_nand_squashfs.pkgtb via Administration > Firmware Upgrade.

This is a beta release. Its filename carries _BETA and the router reports the same string on the dashboard and the About page, so you can always tell which channel a flashed image came from. Stable releases carry no marker.

Verify a download against the attached SHA256SUMS-RT-BE86U-Reaper_v3.1.3.txt.

Corresponding source & reproducibility

The RT-BE86U image for v3.1.3-beta is built from this repository at tag v3.1.3-beta-RT-BE86U: the pinned Asuswrt-Merlin base (3006.102.8-beta2, a7ebfa133a) plus the complete patch series. The tag freezes the exact source that produced it.

• Patches: patches/
• Provenance record: provenance/manifest.json
• How to verify: docs/REPRODUCIBILITY.md and docs/SOURCE-AVAILABILITY.md

The auto-attached Source code (zip/tar.gz) asset below is this repository at tag v3.1.3-beta-RT-BE86U (patches + docs).