RavenSystem/esp-homekit-devices HAA_10.4.6

Home Accessory Architect v10.4.6 Kestrel

on GitHub

Changelog:

• HomeKit: Reverts maximum number of clients to 20 to avoid issues when accessory hub is not available, ignoring Apple specs.
• Bonjour: Reverts default mDNS TTL from 3492-3600 to 4365-4500, ignoring Apple specs.
• Switch and Water Valve: Now it is possible to set a max duration time of 0 to disable auto off.
• Logs: Remove pairing IDs.

Changelog 10.4.5:

• Free Monitor: Several fixes on network requests.
• Free Monitor and History: Added relative index (only negative value) on target characteristic.
• UDP Log: Several fixes when amount of data to send is high.
• Temperature and humidity sensors: Improved startup.
• General: Change unused GPIO management, declaring them at end.
• HAA Installer: Updated to v6.0.7, with fixes for UDP Log, revert back fine tune some tasks sizes, and increase HomeKit config number on firmware update.

Changelog 10.4.4:

• HomeKit: Reduced maximum number of clients from 20 to 8.
• HomeKit: Finetune of AI DRAM thresholds.
• Bonjour: Added current state number to mDNS announce.
• Bonjour: Added random TTL to avoid overlap when several devices reannounce at same time.
• Bonjour: Reduced default mDNS TTL from 4500 to interval 3492-3600.
• DS18B20 Sensor: Added a modified driver to block task when reading data.
• Free Monitor: Fixes several bugs when Network request is used.
• Garage Door: Now, initial state based on sensors is fully opened or closed.
• Window Covering: Fixes missing notification when cover is moving and receive a new target value.
• Reduce some log verbose to reduce flash size.

Changelog 10.4.3:

• Humidifier: Fixes some Service Notifications.
• Lightbulb: Added 200 Service Notification to toggle current state.
• Network Actions: Improves sockets management.
• Fine tune some tasks sizes.
• Improves GPIO initial states.
• HAA Installer: Updated to v6.0.5, with improved GPIO initial states and fine tune some tasks sizes.

Changelog 10.4.2:

• Fixes DHCP Server when HAA WiFi is in Access Point mode.

Changelog 10.4.1:

• HomeKit: Improves AI of low DRAM management.
• Network Request Actions: Fixes Content String Enrichment for TCP RAW and UDP.
• Free Monitor: Fixes low DRAM bug.
• Minor changes at boot.
• HAA Installer: Updated to v6.0.3 with minor changes at boot.

Changelog 10.4.0:

• Air Quality: Added HomeKit compatible extra data.
• General Config: Added "s": key to set accessory number where HAA Setup service is included. Default: "s":1. With "s":0 HAA Setup service is disabled.
• Garage Door: Added "i":<seconds> inching option for autoclose. Default: "i":0, disabled.
• Garage Door: Added -1 value to Service Notifications to reset inching time.
• Network Actions: Fixes memory leak in WOL.
• Humidifier: Added Action 14.
• General: Some DRAM tweaks.
• Setup mode: Web page improvements. Thanks to @andyallcorn (#1761)
• HAA Installer: Updated to v6.0.2 with same setup web page improvements.

Changelog 10.3.2:

• iAirZoning: Fixes actions at boot.

Changelog 10.3.1:

• HeaterCooler & Humidifier: Fixes run actions at boot.
• Window Covering: Removes unnecessary notifications when cover is moving.
• UART, Network and IR/RF Actions: Improves DRAM management.

Changelog 10.3.0:

• Free Monitor Accumulative: New service, a variant of Free Monitor that adds new reads to current value.
• Free Monitor: Added Triggered I2C mode.
• Free Monitor: Now, Service Notifications can be used with any type.
• Lightbulb: Added Zero-Cross mode.
• Lightbulb: Added selective leading PWM mode per channel.
• Lightbulb: Avoid to exec actions 0 and 1 if there is not changes in on/off state.
• Network actions: Fixed UDP request bug on WOL method.
• HomeKit Server: Fine tuning DRAM thresholds.

Changelog v10.2.0:

• Free Monitor: New Types: Pulse Width and UART receiver in text format.
• Free Monitor: Changes in Sensor Type definitions.
• Free Monitor: Fixes UART Receiver bug that was ignoring 0x00 byte.

Changelog v10.1.0:

• Free Monitor: Added length option to fit UART and network received data "bl" : [ min, max ].
• Free Monitor: Fixes target characteristic.
• Fixes Wifi reconnection and Active Roaming mode.
• Minor bug fixes.

Changelog v10.0.0:

• New HomeKit Service: Free Monitor:
  • It is able to retrieve data from different sources and even copy that data to other services:
    • Pulse GPIO.
    • Analog Pin.
    • Network requests.
    • I2C devices.
    • UART0.
• New HomeKit Service: Air Quality.
• Garage Door: Added Actions "12" and "13".
• Lightbulb: Improved DRAM usage at boot.
• Fan: New internal management system.
• Added support to RF emitter using same logic of IR emitter.
• Added ADC (Analog input) to use like a standard GPIO with binary inputs. Declare it as "g":17.
• Added Reboot and Wifi reconnection options with HAA Manager.
• HAA OTA Installer updated to v6.0.0.
• Many CPU improvements.

Read Wiki for more info.