Up to four phones at once on Windows, each as its own camera: for motion capture, multi-angle streaming, or
anything else that wants several cameras.
New: extra cameras (Windows)
- Turn them on: Settings → Camera → Extra cameras. Windows asks for permission once, then apps list
OmniCam 2, OmniCam 3 and OmniCam 4 next to OmniCam. Turning it off removes them again. Apps
that are open may need restarting to see the change. - One phone per camera: with Extra cameras on, the window gets a tab for each camera, and each tab has its
own QR code. Scan camera 2's code with a second phone, camera 3's with a third, and so on. A phone that loses
Wi-Fi comes back to its own camera, and one phone leaving doesn't disturb the others. - All at once in one app: an app can open all four cameras together, which is what motion capture tools
such as FreeMoCap do. In FreeMoCap 2, tick Include virtual cameras when detecting devices in its settings,
and untick any camera that isn't an OmniCam before connecting. - No standby while you set up: while the window shows a live picture, every camera's phone stays at full
frame rate, not only the one whose tab is open. - Shared settings: every camera uses the same output resolution, shape and frame rate. The frame rate
follows camera 1's phone. - Each camera its own way: the rotate button and the phone controls (resolution, front/back, zoom) act on
the camera whose tab is open, so phones mounted differently can each be turned upright. - 480p for older phones: a phone that can't keep up with 720p can film at 480p; it remembers the choice.
- One microphone: only camera 1's phone can be the microphone, because there is one virtual cable.
- Off by default: if you use one phone, nothing changes and apps still list a single OmniCam.
New: a thank-you, and two optional ways to help
- Count this install: OmniCam can now tell its developer that it is in use, with one anonymous message a
month: the app version and your operating system, nothing else, and your IP address is never saved. It is
off unless you say yes, and Settings → About switches it at any time. - Rate OmniCam: five stars, anonymous, sent once, only if you click one.
- Both are asked once, in a note under these release notes. PRIVACY.md shows exactly what is sent.
Fixed
- iPhones held upright arrive upright. An iPhone used to send its picture lying on its side, so it needed
the rotate button while an Android did not. Both now arrive the right way up with no rotation. - A phone that reconnected while on standby stayed at 5 fps, even once an app was using its camera. It now
returns to full frame rate. - Apps that skip "frozen" cameras now list OmniCam. Some motion capture tools read two frames and drop a
camera when they are identical, which OmniCam's placeholder and repeated frames were.
Measured with four simulated phones on one PC (Ryzen 7 5700X): at 720p60 and at 1080p30 all four cameras held
their frame rate with no dropped frames, using well under one CPU core in total. Not on Linux yet, where
OmniCam has one camera.
New install: download OmniCam-Setup-2.5.0.exe below and run it.
Windows SmartScreen may show "Windows protected your PC" (not code-signed yet): click More info -> Run anyway.
Already running OmniCam? Settings -> About -> Check now installs this version for you;
the installer below does the same thing by hand.
Setup, usage and troubleshooting: README.txt below, or the project README.
Linux (x64): OmniCam-2.5.0.AppImage runs on any distribution (chmod +x it, then run it;
it updates itself like the Windows app), or install OmniCam-2.5.0.rpm (Fedora:
sudo dnf install ./OmniCam-2.5.0.rpm) or OmniCam-2.5.0.deb (Debian, Ubuntu:
sudo apt install ./OmniCam-2.5.0.deb) and get new versions here. The camera needs the
v4l2loopback kernel module; OmniCam sets it up with one click once it is installed. See
Linux in the README.
Verify the download (optional):
- SHA-256 of
OmniCam-Setup-2.5.0.exe:4f66aa00dd491dbd2a0b0a3bde6c4b2a24b0af4d7d03e390f2d2f7e80dcda134
PowerShell:Get-FileHash .\OmniCam-Setup-2.5.0.exe - Built by this repository's GitHub Actions from the tagged commit, with a signed provenance attestation:
gh attestation verify OmniCam-Setup-2.5.0.exe --repo Orest-Z/OmniCam