Many small wishes from the issues, two fixes for the 3D view – and everything new is a setting you switch on, so nothing changes unless you want it to.
New
- The wall view is remembered: "Tall walls" or "Cut" stays as you left it after a reload – in the 3D view, in the editor's 3D pane and on the dashboard card, per device (#309 by rolandarends).
- Controls on the right: the floor pictures, star, search and eye can sit on the right instead of the left – header ◧ / ◨, on the card
controls_side: right(#285 by fammastrodaiuto). - Keep the view on floor switches: header ⌖ – switching floors keeps the camera where it is, only its height follows; on the card
keep_view: true(#191 by denisb88). - Device holograms (Energy Pro), all in Editor → Energy → Hologram:
- Hide device cards below (W) – e.g. 1 W, so a card disappears while its device is off (#244 by denisb88).
- Device cards in the house view too – switch them off for the house view, they stay on their floor (#226 by denisb88).
- Device cards in an opened room – shows the cards of a room's devices when you open it (#235 by denisb88).
- Own buttons light up in the star menu while the entity they work on is on (#188 by RobertSorgenfrei).
- Downstand beams and ceiling beams (Architecture pack) have a height above the floor now, e.g. to lower them under a sloped ceiling (#287 by RufusRed80).
- The mouse wheel over a hologram card zooms like anywhere else in the view (#239 by denisb88).
Fixed
- Flickering green strips in passages ("opening without a door"): gone (#290 by itsKXCode).
- Lamp light shining through a wall inside a room (a drywall partition, the inner corner of an L-shaped room) – the light now stops at walls and still passes through doors and openings (#300 by idaho).
- Solar modules on short walls: walls from 0.5 m are offered, e.g. a 0.92 m garden wall (#295 by rolandarends).
- "Back to a device pin" on a lamp turned it into a lamp again on the next load.
- Pro add-ons without furniture no longer show as empty sections in the furniture library and the furniture type list.
How to update
Settings → System → Updates. HACS only looks for new versions every few hours, so a fresh update may not show there yet. Then: HACS → NeonPlan 3D → ⋮ → Update information → Download. Restart Home Assistant and reload the page (Ctrl+F5).
Viele kleine Wünsche aus den Issues, zwei Fehler in der 3D-Ansicht behoben – und alles Neue ist eine Einstellung, die du selbst einschaltest. Ohne dein Zutun bleibt alles, wie es war.
Neu
- Die Wandansicht wird gemerkt: „Wände hoch“ oder „Schnitt“ bleibt nach dem Neuladen, wie du es zuletzt eingestellt hast – in der 3D-Ansicht, in der 3D-Hälfte des Editors und auf der Dashboard-Karte, je Gerät (#309 von rolandarends).
- Bedienleiste rechts: Etagenbilder, Stern, Suche und Auge können rechts statt links sitzen – oben ◧ / ◨, auf der Karte
controls_side: right(#285 von fammastrodaiuto). - Ansicht beim Etagenwechsel halten: oben ⌖ – beim Wechsel der Etage bleibt die Kamera, wo sie ist, nur die Höhe wandert mit; auf der Karte
keep_view: true(#191 von denisb88). - Geräte-Hologramme (Energie Pro), alles unter Editor → Energie → Hologramm:
- Geräte-Karten ausblenden unter (W) – z. B. 1 W, dann verschwindet eine Karte, solange ihr Gerät aus ist (#244 von denisb88).
- Geräte-Karten auch in der Hausansicht – abschalten, dann erscheinen sie nur auf ihrer Etage (#226 von denisb88).
- Geräte-Karten im geöffneten Raum – zeigt beim Öffnen eines Raums die Karten seiner Geräte (#235 von denisb88).
- Eigene Knöpfe leuchten im Stern-Menü, solange ihr Gerät an ist (#188 von RobertSorgenfrei).
- Unterzug und Holzbalkendecke (Pack Architektur) haben jetzt eine Höhe über dem Boden, z. B. um sie unter einer Dachschräge tiefer zu setzen (#287 von RufusRed80).
- Das Mausrad über einer Hologramm-Karte zoomt wie überall sonst (#239 von denisb88).
Behoben
- Grün flackernde Streifen in Durchgängen („Durchbruch ohne Tür“): weg (#290 von itsKXCode).
- Lampenlicht scheint durch eine Wand innerhalb eines Raums (Trockenbauwand, Innenecke eines L-förmigen Raums) – das Licht endet jetzt an Wänden und fällt weiter durch Türen und Durchbrüche (#300 von idaho).
- Solarmodule an kurzen Wänden: Wände ab 0,5 m werden angeboten, z. B. eine 0,92-m-Gartenmauer (#295 von rolandarends).
- „Wieder als Geräte-Pin“ bei einer Leuchte machte beim nächsten Laden wieder eine Leuchte daraus.
- Pro-Erweiterungen ohne Möbel erscheinen nicht mehr als leere Abschnitte in der Möbel-Bibliothek und der Möbel-Auswahl.
So bekommst du das Update
Einstellungen → System → Updates. HACS sucht nur alle paar Stunden nach neuen Versionen, deshalb fehlt ein frisches Update dort manchmal noch. Dann: HACS → NeonPlan 3D → ⋮ → Informationen aktualisieren → Herunterladen. Home Assistant neu starten und die Seite neu laden (Strg+F5).