MarlinFirmware/Marlin 1.1.0-RC2

1.1.0-RC2 "Ten Ton Tauntaun"

on GitHub

Changes: 1.0.2...1.1.0-RC2

• Reduced binary size, depending on your configuration.
• 7 new languages supported:
  • Bulgarian
  • Chinese
  • Czech
  • Danish
  • Galician
  • Japanese Katakana
  • Brazilian Portuguese
• The large pins.h file has been split up into separate files - one for each unique board.
• New electronics supported in 1.1.x - (See boards.h file):
  • BOARD_BRAINWAVE_PRO (85): Brainwave Pro
  • BOARD_BAM_DICE (401): 2PrintBeta BAM&DICE
  • BOARD_BAM_DICE_DUE (402): 2PrintBeta BAM&DICE Due.
  • BOARD_FELIX2 (37): Felix 2.0+
  • BOARD_K8200 (78): Vellemann K8200 Controller (derived from 3Drag Controller)
  • BOARD_MEGACONTROLLER (310): Mega controller
  • BOARD_MINIRAMBO (302): Ultimachine Mini-RAMBo
  • BOARD_MINITRONICS (702): Minitronics v1.0/1.1
  • BOARD_MEGATRONICS_3 (703): Megatronics v3.0
  • BOARD_MKS_BASE (40): MKS BASE 1.0
• Dropped support for BOARD_DUEMILANOVE_328P.
• BOARD_MELZI_1284 renamed to BOARD_MELZI_MAKR3D.
• LCD Probe Z Offset now shows the actual (usually negative) offset value.
• Improved support for Delta, SCARA, and COREXY, and COREXZ kinematics.
• Fixed bugs with Dual X Carriage setups.
• Move parts of Configuration files to Conditionals.h and SanityCheck.h.
• Clean up of temperature code.
• Fix handling of invisible SD files. Files and folders starting with underscore are now visible.
• Enhanced G29 with improved grid bed leveling based on Roxy code. See documentation.
• EEPROM layout updated to V21.
• Short EEPROM output as G-Code – Replay to restore settings. Use M503 S0.
• Added M204 travel acceleration options.
• M204 "P" parameter replaces "S." ("S" retained for backward compatibility.)
• Support for more RAMPS-based boards.
• Support for Mega Controller and Minipanel.
• M404 "N" parameter replaced with "W." ("N" is for line numbers only).
• Improved support for Cyrillic and accented languages.
• Fix M303 so it doesn't swallow commands while running.
• LCD controller knob acceleration. Makes it quicker to select settings values. ENCODER_RATE_MULTIPLIER
• Improved compatibility with various sensors, MAX6675 thermocouple.
• Improved support for M110, with or without the extra N parameter.
• Filament Runout Sensor support. (FILAMENT_RUNOUT_SENSOR)
• Filament width measurement support. (FILAMENT_SENSOR)
• Support for TMC and L6470 stepper drivers.
• Improved support for Texas Instruments DRV8811 stepper drivers.
• Support for the SSD1306 Monochrome 128X32 I2C OLED Graphic Display.
• Better support of G-Code ; comments, \, N line numbers, and * checksums.
• Fixed an issue causing too many "cold extrusion prevented" messages.
• Fixed LCD display of Volumetric Multiplier. Now shows percent instead of scaling value.
• Preliminary support for M111 with debug flags TBD.
• Support for Repetier DEBUG_DRYRUN flag. Use M111 S8.
• Detailed logging to debug Auto Bed Leveling. Use M111 S16.
• Added FAN_MIN_PWM configuration option
  • Cleaned up code formatting