ALLFATHER-BV/wadamesh beta_95

wadamesh beta_95

on GitHub

Test build, on top of beta_94. Stable stays beta_85.

Flash it at flasher.wadamesh.com (switch the toggle to Beta), or update on the device if you have "Get test builds (beta)" turned on.

MeshCore 1.18

wadamesh now runs on MeshCore 1.18, through meshcomod v1.18.0.1. Settings > About shows it under Build.

• The MeshCore app's Command Line works with the device: name, Bluetooth PIN, Wi-Fi, radio settings, airtime and duty cycle, transmit power, receive gain, path hash mode, board and version.
• Remote CLI: a contact you give remote CLI permission in the app can run those commands on your device over the mesh. Anyone else's command arrives in the chat as a message.
• Channel data, pushed sensor telemetry and raw sends over multi-byte paths now reach the app as they do on MeshCore 1.18.
• A device without a clock source starts from 1 March 2026 instead of May 2024, and keeps its time through a restart that was not a power cut.
• Boards without a GPS take up to 5 seconds longer to start: MeshCore 1.18 waits longer for a GPS to answer, so slow modules are found.

New

• Spectrum is redesigned: tiles for the peak, the noise floor, your channel and how busy it is, a filled trace with a peak hold line and a marker on your channel, and a waterfall that stays dark until there is real signal. Band / Channel switches between the whole band and your channel up close; Live / 1 min / 10 min sets the waterfall's history.
• RF Monitor 1.4: tiles, a filled signal chart and the recently heard packets with their type and signal. Tap a packet for who sent it, its route, its margin above what your spreading factor can still decode, its size and its time on the air.
• Airtime 1.6: the channel load as a big figure, average, peak and your own airtime, a chart with the duty-cycle limit, and the receive / transmit split.
• New in the Store: Music. Plays the MP3 and WAV files in a Music folder on the SD card, with shuffle and repeat, and keeps going through the list with the screen off. Runs on every board with a speaker: T-Deck, T-LoRa Pager, T-Display P4, Tanmatsu and T-Deck Max.
• The Store tile shows how many installed apps have an update waiting, checked with the firmware update check.
• T-Deck Max sound (#665 by @Ender436): notification sounds, your own sounds and app audio play through its speaker.
• Emoji (and # on the ThinkNode M9) sit next to Send (#669 by @oumike, reported on Discord), so on the M9 one press of Right from the end of your message reaches them.
• Store apps on the T-Display P4, Tanmatsu and Wio Tracker L2 can read the SD card and play music from it.
• For app makers: rounded panels, bold and large figures, app.on_audio (also with the screen off), and a corrected list of the input events apps receive (SDK guide).

Fixes

• The "SD card could not be read" notice no longer appears when the card works (#667, reported by @900steve). It showed on devices that keep their data on internal storage after an unfinished copy to the card.
• The control panel's clock keeps time while the panel is open (#666, reported by @900steve).
• ThinkNode M9: keyboard light brightness in Settings > Keyboard, like the T-Deck's (#664, asked for by @Buko84).
• The battery widget no longer draws its percentage over a ring too small for it (reported on Discord).
• A Store app that changed a button's text could crash the device; it no longer can.
• RF Monitor named some packet types wrongly, and its Margin tile turned red on a quiet channel.
• Translations: this build's new texts in all 14 languages.

Heltec V4

• The V4 keeps its built-in translations compressed and unpacks only the language you use, which gives it about 330 KB of room again.

Checked on a LilyGo T-Deck (MeshCore 1.18: app sync, the app's Command Line, sending and receiving), and the Music app on a T-Display P4. Every other board builds. Please report what you find with "Send a test report" in Settings > About, or an issue here.